- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9076 (Mitel Networks Corporation) T1/E1/J1 3.3V Single Chip Transceiver PDF資料下載
參數資料
| 型號： | MT9076 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | T1/E1/J1 3.3V Single Chip Transceiver |
| 中文描述： | T1/E1/J1收發3.3V的單芯片收發器 |
| 文件頁數： | 98/160頁 |
| 文件大?。?/td> | 416K |
| 代理商： | MT9076 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁當前第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁
MT9076
Preliminary Information
94
Bit
Name
Functional Description
7
- -
Reserved.
Must be kept at 0 for normal operation.
6
TE
Transmit E bits.
When zero and CRC-4 synchronization is achieved, the E-bits transmit the
received CRC-4 comparison results to the distant end of the link, as per G.703. That is,
when zero and CRC-4 synchronization is lost, the transmit E-bits will be zero. If one, and
CRC-4 synchronization is lost the transmit E-bits will be one.
5
TAIS16
Transmit AIS Time Slot 16
. If one, an all ones signal is transmitted in time slot 16. If zero,
time slot functions normally.
4
TxAO
Transmit All Ones.
When low, this control bit forces a framed or unframed (depending on
the state of Transmit Alarm Control bit 0) all ones to be transmit at TTIP and TRING.
3
Einv
Ebit Error Inversion
. When zero, received Ebits set to zero are counted in the Ebit error
counter and interrupt generator. When one, Ebits set to one are counted in the Ebit error
counter and interrupt generator.
2-0
- - -
Unused
Table 88 - Transmit Alarm Control Word (E1)
(Page 1, Address 11H)
Bit
Name
Functional Description
7
- - -
Unused
.
6
- - -
Unused
.
5
EXZ
Excess Zeros.
Setting this bit causes each occurance of received excess zeros to
increment the Line Code Violation Counter. Excess zeros are defined as 4 or more
successive zeros for HDB3 encoded data, or 16 or more successive zeros for non-HDB3
encoded data.
4
SaBorNi
Sa Bit or Nibble
. Set this bit to determine the criteria for interrupts due to transitions of Sa
bits. If set to one, a change of state of any Sa bit is the criteria. If set to zero, a change of
state of an Sa nibble is the criteria. Note that the selected event can only trigger an interrupt
if the interrupt mask bit SaIM is set high in the Interrupt Mask Word Two - page 1 address
1DH bit 0.
3
RxTRSP
Receive Transparent Mode
. When this bit is set to one, the framing function is disabled on
the receive side. Data coming from the receive line passes through the slip buffer and drives
DSTo with an arbitrary alignment. When zero, the receive framing function operates
normally.
2
TxTRSP
Transmit Transparent Mode
. If one, the MT9076 is in transmit transparent mode. No
framing or signaling is imposed on the data transmit from DSTi onto the line. If zero, it is in
termination mode.
1
TIU1
Transmit International Use One
. When CRC-4 operation is disabled (CSYN=1), this bit is
transmit on the PCM 30 2048 kbit/sec. link in bit position one of time-slot zero of non-frame-
alignment frames. It is reserved for international use and should normally be kept at one. If
CRC processing is used, i.e., CSYN =0, this bit is ignored.
0
TIU0
Transmit International Use Zero
. When CRC-4 operation is disabled (CSYN=1), this bit is
transmit on the PCM 30 2048 kbit/sec. link in bit position one of time-slot zero of frame-
alignment frames. It is reserved for international use and should normally be kept at one. If
CRC processing is used, i.e., CSYN =0, this bit is ignored.
Table 89 - TS0 Control Word (E1)
(Page 1, Address 12H)
相關PDF資料 |
PDF描述 |
|---|---|
| MT9076AB | T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076 | T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器) |
| MT9079 | Advanced Controller for E1(先進的E1幀調節器和控制器) |
| MT9080B | SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊) |
| MT90810 | Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9076AB | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076AP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076B | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver |
| MT9076BB | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
| MT9076BB1 | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
發布緊急采購，3分鐘左右您將得到回復。