- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9076 (Mitel Networks Corporation) T1/E1/J1 3.3V Single Chip Transceiver PDF資料下載
參數資料
| 型號： | MT9076 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | T1/E1/J1 3.3V Single Chip Transceiver |
| 中文描述： | T1/E1/J1收發3.3V的單芯片收發器 |
| 文件頁數： | 28/160頁 |
| 文件大小： | 416K |
| 代理商： | MT9076 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁
MT9076
Preliminary Information
24
In Line Synchronous mode, the clock extracted from the receive data is dejittered using the internal PLL
and then output on pin C4b. Pin Exclk provides the extracted receive clock before it has been dejittered.
The transmit data is synchronous to the clean receive clock.
In Free-Run mode the transmit data is synchronized to the internally generated clock. The internal clock
is output on pin C4b. The clock signal extracted from the receive data is not dejittered and is output
directly on Exclk.
2.1
Jitter Attenuator FIFO
In System Bus Synchronous operation, a data buffer is required between the jittered input clock and the clean
transmit clock. In normal T1 mode, the transmit slip buffer performs this function. In T1 IMA mode, the transmit
slip buffer is unused, instead a jitter attenuator FIFO is employed. In an E1 mode System Bus Synchronous
configuration, the jitter attenuator FIFO is always used. In this case the C4b signal clocks the data into the
FIFO, the PLL de-jitters the C4b clock and the resulting clean C4b signal clocks the data out of the FIFO.
The JA meets the jitter transfer characteristics as proposed by ETSI ETS 300 011, G.735 and the relevant
recommendations as shown in Figure 12. The JA FIFO depth can be selected to be from 16 to 128 words deep,
in multiples of 16 (2-bit) words. Its read pointer can be centered by changing the JFC bit (address 13H of page
02H) to provide maximum jitter tolerance. If the read pointer should come within 4 bits of either end of the
FIFO, the read clock frequency will be increased or decreased by 0.0625 UI to correct the situation. The
maximum time needed to centre is T
max
= 3904
Depth ns, where Depth is the selected JA FIFO depth. During
this time the JA will not attenuate jitter.
2.2
IMA Mode
2.2.1
In T1 IMA Mode, neither the transmit nor the receive slip buffers are activated. Channel Associated signaling
(CAS) and HDLC operation is not supported. The input pin C4b accepts a 1.544 MHz clock and it clocks
incoming data from DSTi into a jitter attenuator FIFO. This clock is dejittered with the internal PLL. The
dejittered clock clocks data out of the FIFO for transmission onto the line. Receive clock (1.544 MHz) and data
is extracted from the line and routed to pins Exclk and DSTo respectively. The receive clock Exclk is not
dejittered before being driven off chip. For operation in IMA mode, the MT9076 should be programmed in
System Bus Synchronous mode (BS/LS and S/FR/Exclki set high).
T1 Mode
2.2.2
In E1 IMA Mode neither the transmit nor the receive slip buffers are activated. The input pin C4b accepts a
2.048 MHz clock and it clocks incoming data from DSTi into a jitter attenuator FIFO. This clock is dejittered with
the internal PLL. The dejittered clock clocks data out of the FIFO for transmission onto the line. Receive clock
(2.048 MHz) and data is extracted from the line and routed to pins Exclk and DSTo respectively. The receive
clock Exclk is not dejittered before being driven off chip. For operation in IMA mode, the MT9076 should be
programmed in System Bus Synchronous mode (BS/LS and S/FR/Exclki set high).
E1 Mode
3.0
The Digital Interface
3.1
T1 Digital Interface
In T1 mode, DS1 frames are 193 bits long and are transmitted at a frame repetition rate of 8000 Hz, which
results in an aggregate bit rate of 193 bits x 8000/sec= 1.544 Mbits/sec. The actual bit rate is 1.544 Mbits/sec
+/-50 ppm optionally encoded in B8ZS format. The Zero Suppression control register (page 1, address 15H,)
selects either B8ZS encoding, forced one stuffing or alternate mark inversion (AMI) encoding. Basic frames are
divided into 24 time slots numbered 1 to 24. Each time slot is 8 bits in length and is transmitted most significant
bit first (numbered bit 1). This results in a single time slot data rate of 8 bits x 8000/sec. = 64 kbits/sec.
相關PDF資料 |
PDF描述 |
|---|---|
| MT9076AB | T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076 | T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器) |
| MT9079 | Advanced Controller for E1(先進的E1幀調節器和控制器) |
| MT9080B | SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊) |
| MT90810 | Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9076AB | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076AP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076B | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver |
| MT9076BB | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
| MT9076BB1 | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
發布緊急采購，3分鐘左右您將得到回復。