參數資料
型號： MQ80C154-16P883
廠商： TEMIC SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, 16 MHz, MICROCONTROLLER, CQFP44
文件頁數： 128/142頁
文件大?。?/td> 61013K
代理商： MQ80C154-16P883
213
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P [DATASHEET]
8285E–AVR–02/2013
level execution of Assembly programs assembled with Atmel Corporation’s AVR Assembler and C programs com-
piled with third party vendors’ compilers.
AVR Studio runs under Microsoft Windows 95/98/2000, Windows NT and Windows XP.
For a full description of the AVR Studio, please refer to the AVR Studio User Guide. Only highlights are presented
in this document.
All necessary execution commands are available in AVR Studio, both on source level and on disassembly level.
The user can execute the program, single step through the code either by tracing into or stepping over functions,
step out of functions, place the cursor on a statement and execute until the statement is reached, stop the execu-
tion, and reset the execution target. In addition, the user can have an unlimited number of code Break Points (using
the BREAK instruction) and up to two data memory Break Points, alternatively combined as a mask (range) Break
Point.
24.7
On-chip Debug Specific JTAG Instructions
The On-chip debug support is considered being private JTAG instructions, and distributed within Atmel and to
selected third party vendors only. Instruction opcodes are listed for reference.
24.7.1
PRIVATE0; 0x8
Private JTAG instruction for accessing On-chip debug system.
24.7.2
PRIVATE1; 0x9
Private JTAG instruction for accessing On-chip debug system.
24.7.3
PRIVATE2; 0xA
Private JTAG instruction for accessing On-chip debug system.
24.7.4
PRIVATE3; 0xB
Private JTAG instruction for accessing On-chip debug system.
24.8
Using the JTAG Programming Capabilities
Programming of AVR parts via JTAG is performed via the 4-pin JTAG port, TCK, TMS, TDI, and TDO. These are
the only pins that need to be controlled/observed to perform JTAG programming (in addition to power pins). It is not
required to apply 12V externally. The JTAGEN Fuse must be programmed and the JTD bit in the MCUCR Register
must be cleared to enable the JTAG Test Access Port. See ”Boundary-scan Related Register in I/O Memory” on
The JTAG programming capability supports:
Flash programming and verifying
EEPROM programming and verifying
Fuse programming and verifying
Lock bit programming and verifying
The Lock bit security is exactly as in parallel programming mode. If the Lock bits LB1 or LB2 are programmed, the
OCDEN Fuse cannot be programmed unless first doing a chip erase. This is a security feature that ensures no
back-door exists for reading out the content of a secured device.
The details on programming through the JTAG interface and programming specific JTAG instructions are given in
相關PDF資料
PDF描述
MQ83C154XXX-L16/883D 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQFP44
MQ83C154CXXX-25/883R 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44
MR80C154-L16/883R 8-BIT, 16 MHz, MICROCONTROLLER, CQCC44
MQ83C154CXXX-L16P883R 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQFP44
MR83C154CXXX-20P883R 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQCC44
相關代理商/技術參數
參數描述
MQ80C154-20 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C154-25 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C154-30 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C154-36 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C154-L16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*