參數資料
型號: LPC2368FBD100
廠商: NXP Semiconductors N.V.
元件分類: 數學處理器
英文描述: ARM7 with 512 kB flash, 58 kB SRAM, Ethernet, USB 2.0 Device, CAN, SD-MMC, and 10-bit ADC
封裝: LPC2368FBD100<SOT407-1 (LQFP100)|<<http://www.nxp.com/packages/SOT407-1.html<1<Always Pb-free,;
文件頁數: 12/18頁
文件大?。?/td> 220K
代理商: LPC2368FBD100
ES_LPC2368
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Errata sheet
Rev. 9 — 20 April 2011
12 of 18
NXP Semiconductors
ES_LPC2368
Errata sheet LPC2368
3.15 MAM.1: Under certain conditions in MAM Mode 2 code execution out
of internal flash can fail
Introduction:
The MAM block maximizes the performance of the ARM processor when it is running
code in flash memory. It includes three 128-bit buffers called the Prefetch Buffer, the
Branch Trail Buffer and the data buffer. It can operate in 3 modes; Mode 0 (MAM off),
Mode 1 (MAM partially enabled) and Mode 2 (MAM fully enabled).
Problem:
Under certain conditions when the MAM is fully enabled (Mode 2) code execution from
internal flash can fail. The conditions under which the problem can occur is dependent on
the code itself along with its positioning within the flash memory.
Work-around:
If the above problem is encountered then Mode 2 should not be used. Instead, partially
enable the MAM using Mode 1.
3.16 CAN.1: Data Overrun condition can lock the CAN controller
Introduction:
Each CAN controller provides a double Receive Buffer (RBX) per CAN channel to store
incoming messages until they are processed by the CPU. Software task should read and
save received data as soon as a message reception is signaled.
In cases where both receive buffers are filled and the contents are not read before the
third message comes in, a CAN Data Overrun situation is signaled. This condition is
signaled via the Status register and the Data Overrun Interrupt (if enabled).
Problem:
In a Data Overrun condition, the CAN controller is locked from further message reception.
Work-around:
1. Recovering from this situation is only possible with a soft reset to the CAN controller.
2. If software cannot read all messages in time before a third message comes in, it is
recommend to change the acceptance filtering by adding further acceptance filter
group(s) for messages, which are normally rejected. With this approach, the third
incoming message is accepted and the Data Overrun condition is avoided. These
additional messages are received with the corresponding group index number can be
easily identified and rejected by software.
相關PDF資料
PDF描述
LPC2377FBD144 Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC
LPC2378FBD144 Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC
LPC2387FBD100 Single-chip 16-bit-32-bit MCU; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
LPC2388FBD144 Single-chip 16-bit-32-bit micro; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
LPC2420FBD208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
相關代理商/技術參數
參數描述
LPC2368FBD100,551 功能描述:ARM微控制器 - MCU ARM7 512KF/USB/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2368FBD100/CP32 制造商:NXP Semiconductors 功能描述:- Tape and Reel
LPC2368FBD100551 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU 72MHZ LQFP-100
LPC2368FET100 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit ocontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2368FET100,518 功能描述:ARM微控制器 - MCU 16/32 bit micro RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT