參數資料
型號: LPC2368FBD100
廠商: NXP Semiconductors N.V.
元件分類: 數學處理器
英文描述: ARM7 with 512 kB flash, 58 kB SRAM, Ethernet, USB 2.0 Device, CAN, SD-MMC, and 10-bit ADC
封裝: LPC2368FBD100<SOT407-1 (LQFP100)|<<http://www.nxp.com/packages/SOT407-1.html<1<Always Pb-free,;
文件頁數: 10/18頁
文件大?。?/td> 220K
代理商: LPC2368FBD100
ES_LPC2368
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Errata sheet
Rev. 9 — 20 April 2011
10 of 18
NXP Semiconductors
ES_LPC2368
Errata sheet LPC2368
3.12 WDT.1: Accessing non-Watchdog APB registers in the middle of the
feed sequence causes a reset
Introduction:
The Watchdog timer can reset the microcontroller within a reasonable amount of time if it
enters an erroneous state.
Problem:
After writing 0xAA to WDFEED, any APB register access other than writing 0x55 to
WDFEED may cause an immediate reset.
Work-around:
Avoid APB accesses in the middle of the feed sequence. This implies that interrupts and
the GPDMA should be disabled while feeding the Watchdog.
3.13 Core.1: Incorrect update of the Abort Link register in Thumb state
Introduction:
If the processor is in Thumb state and executing the code sequence STR, STMIA or
PUSH followed by a PC relative load, and the STR, STMIA or PUSH is aborted, the PC is
saved to the abort link register.
Problem:
In this situation the PC is saved to the abort link register in word resolution, instead of
half-word resolution.
Conditions:
The processor must be in Thumb state, and the following sequence must occur:
<any instruction>
<STR, STMIA, PUSH> <---- data abort on this instruction
LDR rn, [pc,#offset]
In this case the PC is saved to the link register R14_abt in only word resolution, not
half-word resolution. The effect is that the link register holds an address that could be #2
less than it should be, so any abort handler could return to one instruction earlier than
intended.
Work-around:
In a system that does not use Thumb state, there will be no problem.
In a system that uses Thumb state but does not use data aborts, or does not try to use
data aborts in a recoverable manner, there will be no problem.
Otherwise the workaround is to ensure that a STR, STMIA or PUSH cannot precede a
PC-relative load. One method for this is to add a NOP before any PC-relative load
instruction. However this is would have to be done manually.
相關PDF資料
PDF描述
LPC2377FBD144 Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC
LPC2378FBD144 Single-chip 16-bit-32-bit microcontrollers; 512 kB flash with ISP-IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC-DAC
LPC2387FBD100 Single-chip 16-bit-32-bit MCU; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
LPC2388FBD144 Single-chip 16-bit-32-bit micro; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
LPC2420FBD208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
相關代理商/技術參數
參數描述
LPC2368FBD100,551 功能描述:ARM微控制器 - MCU ARM7 512KF/USB/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2368FBD100/CP32 制造商:NXP Semiconductors 功能描述:- Tape and Reel
LPC2368FBD100551 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU 72MHZ LQFP-100
LPC2368FET100 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit ocontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
LPC2368FET100,518 功能描述:ARM微控制器 - MCU 16/32 bit micro RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT