參數資料
型號： ISPPAC-POWR1014A
廠商： Lattice Semiconductor Corporation
英文描述： In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
中文描述： 在系統可編程電源監控器，復位發生器和排序控制器
文件頁數： 32/45頁
文件大小： 999K
代理商： ISPPAC-POWR1014A
Lattice Semiconductor
ispPAC-POWR1014/A Data Sheet
32
Three special purpose pins, VCCPROG, ATDI and TDISEL, enable programming of the un-programmed ispPAC-
POWR1014/A under such circumstances. The VCCPROG pin powers just the programming circuitry of the ispPAC-
POWR1014/A device. The ATDI pin provides an alternate connection to the JTAG header while bypassing all the
un-powered devices in the JTAG chain. TDISEL pin enables switching between the ATDI and the standard JTAG
signal TDI. When the internally pulled-up TDISEL = 1, standard TDI pin is enabled and when the TDISEL = 0, ATDI
is enabled.
In order to use this feature the JTAG signals of the ispPAC-POWR1014/A are connected to the header as shown in
Figure 26.
N
ote: The ispPAC-POWR1014/A should be the last device in the JTAG chain.
Figure 26. ispPAC-POWR1014/A Alternate TDI Configuration Diagram
Alternate TDI Selection Via JTAG Command
When the TDISEL pin held high and four consecutive IDCODE instructions are issued, ispPAC-POWR1014/A
responds by making its active JTAG data input the ATDI pin. When ATDI is selected, data on its TDI pin is ignored
until the JTAG state machine returns to the Test-Logic-Reset state.
This method of selecting ATDI takes advantage of the fact that a JTAG device with an IDCODE register will auto-
matically load its unique IDCODE instruction into the Instruction Register after a Test-Logic-Reset. This JTAG capa-
bility permits blind interrogation of devices so that their location in a serial chain can be identified without having to
know anything about them in advance. A blind interrogation can be made using only the TMS and TCLK control
pins, which means TDI and TDO are not required for performing the operation. Figure 27 illustrates the logic for
selecting whether the TDI or ATDI pin is the active data input to ispPAC-POWR1014/A.
TDI
ATDI
T
TDO
T
TDI
T
TDO
T
TDI
TCK
TMS
V
C
V
C
V
C
V
C
TDISEL
TDO
T
V
C
2.
Initial Po
w
er
S
u
pply T
u
rn-On
3.
Se
qu
enced Po
w
er
S
u
pply T
u
rn-on
JTAG Signal
Connector
Other JTAG
Device(s)
ispPAC-POWR
1014A
1.
Po
w
er for
Programming
PO
W
R1014A
V
C
相關PDF資料
PDF描述
ISPPAC-POWR1014A-01T48I In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR1014A-01TN48I In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR6AT6-01N32I In-System Programmable Power Supply Monitoring and Margining Controller
ISPPAC-POWR6AT6-01NN32I In-System Programmable Power Supply Monitoring and Margining Controller
ISPPAC10 In-System Programmable Analog Circuit
相關代理商/技術參數
參數描述
ISPPACPOWR1014A01T48I 制造商:Lattice Semiconductor Corporation 功能描述:Volt Supervisor Sequencer/Monitor 48-Pin TQFP
ispPAC-POWR1014A-01T48I 功能描述:監控電路 ispPAC-POWR1014 w/ A DC I RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
ISPPAC-POWR1014A-01TN148I 制造商:Lattice Semiconductor Corporation 功能描述:IC POWER SUPP MONITOR SMD TQFP48 制造商:Lattice Semiconductor Corporation 功能描述:IC, POWER SUPP MONITOR, SMD, TQFP48
ispPAC-POWR1014A-01TN48I 功能描述:監控電路 ispPAC-POWR1014 w/ A DC I RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
ISPPACPOWR1014A01TN48IAG6 制造商:Lattice Semiconductor Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*