參數資料
型號： ISPPAC-POWR1014A
廠商： Lattice Semiconductor Corporation
英文描述： In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
中文描述： 在系統可編程電源監控器，復位發生器和排序控制器
文件頁數： 18/45頁
文件大?。?/td> 999K
代理商： ISPPAC-POWR1014A
Lattice Semiconductor
ispPAC-POWR1014/A Data Sheet
18
VMON Voltage Measurement with the On-chip Analog to Digital Converter (ADC, ispPAC-
POWR1014A Only)
The ispPAC-POWR1014A has an on-chip analog to digital converter that can be used for measuring the voltages at
the VMO
N
inputs.
Figure 8. ADC Monitoring VMON1 to VMON10
Figure 8 shows the ADC circuit arrangement within the ispPAC-POWR1014A device. The ADC can measure all
analog input voltages through the multiplexer, ADC MUX. The programmable attenuator between the ADC mux and
the ADC can be configured as divided-by-3 or divided-by-1 (no attenuation). The divided-by-3 setting is used to
measure voltages from 0V to 6V range and divided-by-1 setting is used to measure the voltages from 0V to 2V
range.
A microcontroller can place a request for any VMO
N
voltage measurement at any time through the I
2
C bus (isp-
PAC-POWR1014A only). Upon the receipt of an I
2
C command, the ADC will be connected to the I
2
C selected
VMO
N
through the ADC MUX. The ADC output is then latched into the I
2
C readout registers.
Calculation
The algorithm to convert the ADC code to the corresponding voltage takes into consideration the attenuation bit
value. In other words, if the attenuation bit is set, then the 10-bit ADC result is automatically multiplied by 3 to cal-
culate the actual voltage at that VMO
N
input. Thus, the I
2
C readout register is 12 bits instead of 10 bits. The follow-
ing formula can always be used to calculate the actual voltage from the ADC code.
Voltage at the VMONx Pins
VMO
N
= I
2
C Readout Register (12 bits
1
, converted to decimal) * 2mV
1
N
ote: ADC_VALUE_HIGH (8 bits), ADC_VALUE_LOW (4 bits) read from I
2
C/SMBUS interface (ispPAC-POWR1014A only).
V
MON1
V
MON2
V
MON3
V
MON10
V
DDA
V
CCINP
ADC
MUX
ADC
Programma
b
le Analog
Atten
u
ator
Programma
b
le
Digital M
u
ltiplier
Internal
V
REF- 2.04
8V
4
10
x3 / x1
÷
3 /
÷
1
12
To I
2
C Reado
u
t Register
(ispPAC-PO
W
R1014A Only)
5
From I
2
C ADC MUX Register
(ispPAC-PO
W
R1014A Only)
1
相關PDF資料
PDF描述
ISPPAC-POWR1014A-01T48I In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR1014A-01TN48I In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR6AT6-01N32I In-System Programmable Power Supply Monitoring and Margining Controller
ISPPAC-POWR6AT6-01NN32I In-System Programmable Power Supply Monitoring and Margining Controller
ISPPAC10 In-System Programmable Analog Circuit
相關代理商/技術參數
參數描述
ISPPACPOWR1014A01T48I 制造商:Lattice Semiconductor Corporation 功能描述:Volt Supervisor Sequencer/Monitor 48-Pin TQFP
ispPAC-POWR1014A-01T48I 功能描述:監控電路 ispPAC-POWR1014 w/ A DC I RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
ISPPAC-POWR1014A-01TN148I 制造商:Lattice Semiconductor Corporation 功能描述:IC POWER SUPP MONITOR SMD TQFP48 制造商:Lattice Semiconductor Corporation 功能描述:IC, POWER SUPP MONITOR, SMD, TQFP48
ispPAC-POWR1014A-01TN48I 功能描述:監控電路 ispPAC-POWR1014 w/ A DC I RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
ISPPACPOWR1014A01TN48IAG6 制造商:Lattice Semiconductor Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*