參數資料
型號: ISPPAC-POWR1014A
廠商: Lattice Semiconductor Corporation
英文描述: In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
中文描述: 在系統可編程電源監控器,復位發生器和排序控制器
文件頁數: 13/45頁
文件大?。?/td> 999K
代理商: ISPPAC-POWR1014A
Lattice Semiconductor
ispPAC-POWR1014/A Data Sheet
13
Figure 6. ispPAC-POWR1014/A Voltage Monitors
Figure 6 shows the functional block diagram of one of the 10 voltage monitor inputs - ‘x’ (where x = 1...10). Each
voltage monitor can be divided into three sections: Analog Input, Window Control, and Filtering.
The voltage input is monitored by two individually programmable trip-point comparators, shown as CompA and
CompB. Table 1 shows all trip points and the range to which any comparator’s threshold can be set.
Each comparator outputs a HIGH signal to the PLD array if the voltage at its positive terminal is greater than its pro-
grammed trip point setting, otherwise it outputs a LOW signal.
A hysteresis of approximately 1% of the setpoint is provided by the comparators to reduce false triggering as a
result of input noise. The hysteresis provided by the voltage monitor is a function of the input divider setting. Table 3
lists the typical hysteresis versus voltage monitor trip-point.
AGOOD Logic Signal
All the VMO
N
comparators auto-calibrate immediately after a power-on reset event. During this time, the digital
glitch filters are also initialized. This process completion is signalled by an internally generated logic signal:
AGOOD. All logic using the VMO
N
comparator logic signals must wait for the AGOOD signal to become active.
Programmable Over-Voltage and Under-Voltage Thresholds
Figure 7 (a) shows the power supply ramp-up and ramp-down voltage waveforms. Because of hysteresis, the com-
parator outputs change state at different thresholds depending on the direction of excursion of the monitored power
supply.
Glitch
Filter
M
Trip Point A
+
+
Comp A
Comp B
Comp A/
W
indo
w
Select
V
MONxB
Logic
Signal
V
MONx
Trip Point B
Analog Inp
u
t
W
indo
w
Control
Filtering
ispPAC-PO
W
R1014/A
To ADC
(PO
W
R1014A only)
V
MONxA
Logic
Signal
PLD
Array
V
MONx Stat
u
s
I
2
C Interface
Unit (PO
W
R1014A
only)
Glitch
Filter
相關PDF資料
PDF描述
ISPPAC-POWR1014A-01T48I In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR1014A-01TN48I In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
ISPPAC-POWR6AT6-01N32I In-System Programmable Power Supply Monitoring and Margining Controller
ISPPAC-POWR6AT6-01NN32I In-System Programmable Power Supply Monitoring and Margining Controller
ISPPAC10 In-System Programmable Analog Circuit
相關代理商/技術參數
參數描述
ISPPACPOWR1014A01T48I 制造商:Lattice Semiconductor Corporation 功能描述:Volt Supervisor Sequencer/Monitor 48-Pin TQFP
ispPAC-POWR1014A-01T48I 功能描述:監控電路 ispPAC-POWR1014 w/ A DC I RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
ISPPAC-POWR1014A-01TN148I 制造商:Lattice Semiconductor Corporation 功能描述:IC POWER SUPP MONITOR SMD TQFP48 制造商:Lattice Semiconductor Corporation 功能描述:IC, POWER SUPP MONITOR, SMD, TQFP48
ispPAC-POWR1014A-01TN48I 功能描述:監控電路 ispPAC-POWR1014 w/ A DC I RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
ISPPACPOWR1014A01TN48IAG6 制造商:Lattice Semiconductor Corporation 功能描述: