參數資料
型號： HT82A851R
廠商： Holtek Semiconductor Inc.
英文描述： USB Audio MCU
中文描述： USB音頻控制器
文件頁數： 11/43頁
文件大?。?/td> 304K
代理商： HT82A851R
HT82A851R
Rev. 1.20
11
June 15, 2007
If the instruction clock is selected as the WDT clock
source,theWDToperatesinthesamemannerexceptin
the halt mode. In the HALT mode, the WDT stops count-
ing and lose its protecting purpose. In this situation the
logic can only be re-started by external logic. The high
nibbleoftheWDTSisreservedfortheDACwritemode.
The WDT overflow under normal operation initializes a
chip reset and sets the status bit TO . In the HALT
mode, the overflow initializes a warm reset , and only
the program counter and stack pointer are reset to zero.
To clear the contents of the WDT, there are three meth-
ods to be adopted, i.e., an external reset (a low level to
RESET), a software instruction, and a HALT instruc-
tion. There are two types of software instructions; CLR
WDT
and the other set
CLR WDT1
and
CLR
WDT2 . Of these two types of instruction, only one type
of instruction can be active at a time depending on the
configuration option CLR WDT times selection option.
If the CLR WDT is selected (i.e., CLR WDT times
equal one), any execution of the CLR WDT instruction
clears the WDT. In the case that CLR WDT1 and CLR
WDT2 are chosen (i.e., CLR WDT times equal two),
these two instructions have to be executed to clear the
WDT; otherwise, the WDT may reset the chip due to a
time-out.
Power Down Operation
HALT
The Power-down mode is entered by the execution of a
HALT instruction and results in the following:
The system oscillator will be turned off but the WDT
oscillator keeps running if the internal WDT oscillator
is selected.
The contents of the on-chip data memory and regis-
ters remain unchanged.
The WDT and WDT prescaler will be cleared and will
start counting again if the WDT clock is sourced from
the internal WDT oscillator.
All of the I/O ports remain in their original condition.
The PDF flag is set and the TO flag is cleared.
The system can leave the Power-down mode by means
of an external reset, an interrupt, an external falling
edge signal on port A or a WDT overflow. An external
reset causes a device initialisation and the WDT
overflowperformsa warmreset .AftertheTOandPDF
flags are examined, the cause for the device reset can
be determined. The PDF flag is cleared by a system
power-up or by executing the CLR WDT instruction
and is set when executing the HALT instruction. The
TO flag is set if the WDT time-out occurs, and causes a
wake-up that only resets the program counter and SP;
the others remain in their original status.
A port A wake-up and interrupt methods can be
considered as a continuation of normal execution. Each
pin in port A can be independently selected to wake-up
the device using configuration options. After awakening
from an I/O port stimulus, the program will resume
execution at the next instruction. If the device is
awakened from an interrupt, two sequence may occur. If
the related interrupt is disabled or the interrupt is
enabled but the stack is full, the program will resume
execution at the next instruction. If the interrupt is
enabled and the stack is not full, the regular interrupt
responsetakesplace.Ifaninterruptrequestflagissetto
1 before entering the Power-down mode, the wake-up
function of the related interrupt will be disabled. Once a
wake-up event occurs, it takes 1024 t
SYS
(system clock
periods) to resume normal operation, i.e., a dummy
period is inserted. If the wake-up results from an
%
&
> ( 0
: < A
%
%
&
+ < A
%
: <
< %
%
<
) *
1
>
&
%
Watchdog Timer
Bit No.
Label
Function
0
1
2
WS0
WS1
WS2
Watchdog Timer division ratio selection bits
Bit 2,1,0 = 000, Division Ratio = 1:1
Bit 2,1,0 = 001, Division Ratio = 1:2
Bit 2,1,0 = 010, Division Ratio = 1:4
Bit 2,1,0 = 011, Division Ratio = 1:8
Bit 2,1,0 = 100, Division Ratio = 1:16
Bit 2,1,0 = 101, Division Ratio = 1:32
Bit 2,1,0 = 110, Division Ratio = 1:64
Bit 2,1,0 = 111, Division Ratio = 1:128
3~7
Unused bit, read as 0
WDTS (09H) Register
相關PDF資料
PDF描述
HT82J30A 16 Channel A/D MCU with SPI Interface
HT82J30R 16 Channel A/D MCU with SPI Interface
HT82J927A USB Gamepad
HT82J97E USB Joystick Encoder 8-Bit OTP MCU
HT82J97E-20SOP-A USB Joystick Encoder 8-Bit OTP MCU
相關代理商/技術參數
參數描述
HT82B40A 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O MCU with USB Interface
HT82B40R 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O MCU with USB Interface
HT82B40R_11 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O MCU with USB Interface
HT82B42R 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O MCU with USB Interface
HT82B42RE 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O MCU with USB Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*