- 您現在的位置：買賣IC網 > PDF目錄370499 > HDMP-1022 Audio Power Amplifier; Speaker Channels:Mono; Headphone Channels:Mono; Output Power, Po:2W; Load Impedance Min:8ohm; Supply Voltage Max:24V; Supply Voltage Min:6V PDF資料下載
參數資料
| 型號： | HDMP-1022 |
| 英文描述： | Audio Power Amplifier; Speaker Channels:Mono; Headphone Channels:Mono; Output Power, Po:2W; Load Impedance Min:8ohm; Supply Voltage Max:24V; Supply Voltage Min:6V |
| 中文描述： | 低成本千兆速率發送/接收芯片組配備TTL的I / O |
| 文件頁數： | 20/40頁 |
| 文件大?。?/td> | 321K |
| 代理商： | HDMP-1022 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
635
Rx I/O Definition (cont’d.)
Name
Pin
ERROR
40
Type
O-TTL
Signal
Received Data Error:
Asserted when a frame is received that does
not correspond to either a
valid
Data, Control, or Fill frame encoding.
When FLAGSEL is not active, the Rx chip also tests for strict
alternation of flag bits during data frames. A flag bit alternation
error will also cause an ERROR indication.
Frequency Detector Disable Input:
When active, this input
disables the Rx PLL Frequency detector and enables a phase detector.
The Frequency detector is used during the start-up sequence to
acquire wide-band lock on Fill Frames, but must be disabled prior to
sending data patterns. This input is normally controlled by the Rx
state machine.
Fill Frame Status:
During a given STRBOUT clock cycle, if neither
DAV, CAV, or ERROR are active, then the currently received frame
is a Fill frame. The type of fill frame received is indicated by the FF
pin. If FF is low, then FF0 has been received. If FF is high, then
either FF1a or FF1b has been received.
Flag Bit:
If both Tx and Rx have FLAGSEL asserted, this output
indicates the value of the transmitted flag bit, then this received bit
can be treated just like an extra data bit. If both Tx and Rx have
FLAGSEL set to low, FLAG is used to differentiate the even frame
from the odd frame in the line code.
Flag Bit Mode Select:
When this input is high, the extra FLAG bit
output is effectively an extra transparent data bit. Otherwise, the
FLAG bit is checked for alternation during data frames. Any break in
strict alternation results in an ERROR indication to the user.
Loop Back Serial Data Input:
Use this input when LOOPEN is
active. Unlike the DIN, DIN* inputs, this input does not have a cable
equalizer. In normal usage, this input will be connected to the Tx
chip LOUT, LOUT* outputs. This allows the user to check the
near-end functionality of the Tx and Rx pair independent of the
transmission medium.
Loop Back Control:
When asserted, this signal causes the loop back
data inputs LIN, LIN* to be used instead of the normal data inputs
DIN, DIN*.
Link Ready Indicator:
This active-low output is a retimed version
of the ACTIVE input. ACTIVE is normally driven by the Rx state
machine output. LINKRDY* then indicates that the startup sequence
is complete and that the data and control indications are valid.
16 or 20 Bit Word Select:
When this signal is high, the link operates
in 20 Bit data reception mode. Otherwise, the link operates in 16 Bit
mode and data outputs D16-D19 are undefined.
Temperature Sense Diode:
Used during wafer and package test
only. It should be left open.
FDIS
20
I-TTL
FF
39
O-TTL
FLAG
45
O-TTL
FLAGSEL
34
I-TTL
LIN
LIN*
18
17
I-H50
LOOPEN
16
I-TTL
LINKRDY*
36
O-TTL
M20SEL
30
I-TTL
TEMP
TEMP*
77
76
T
相關PDF資料 |
PDF描述 |
|---|---|
| HDMP-1024 | Low Cost Gigabit Rate Receive Chip Set with TTL I/Os(帶TTL輸入/輸出的低價格千兆位速率接收芯片) |
| HDMP-1032 | 1.4 GBd Transmitter Chip Set with CIMT Encoder/Decoder and Variable Data Rate(帶CIMT編碼器/譯碼器和變量數據速率的1.4 GBd 傳送器) |
| HDMP-1034 | 1.4 GBd Receiver Chip Set with CIMT Encoder/Decoder and Variable Data Rate(帶CIMT編碼器/譯碼器和變量數據速率的1.4 GBd 接收器) |
| HDMP-1512 | Fibre Channel Transmitter Chipset(光纖通道傳送芯片) |
| HDMP-1514 | Fibre Channel Receiver Chipset(光纖通道接收芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HDMP-1024 | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Low Cost Gigabit Rate Transmit/Receive Chip Set with TTL I/Os |
| HDMP-1032 | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:1.4 GBd Transmitter/Receiver Chip Set with CIMT Encoder/Decoder and Variable Data Rate |
| HDMP-1032A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1.4 GBd Transmitter Chip with CIMT Encoder/Decoder and Variable Data Rate |
| HDMP-1034 | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:1.4 GBd Transmitter/Receiver Chip Set with CIMT Encoder/Decoder and Variable Data Rate |
| HDMP-1034A | 制造商:HP 制造商全稱:Agilent(Hewlett-Packard) 功能描述:Transmitter/Receiver Chip Set |
發布緊急采購，3分鐘左右您將得到回復。