- 您現在的位置：買賣IC網 > PDF目錄385311 > GS1559-CBE2 (Gennum Corporation) GS1559 HD-LINX-TM II Multi-Rate Deserializer with Loop-Through Cable Driver PDF資料下載
參數資料
| 型號： | GS1559-CBE2 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS1559 HD-LINX-TM II Multi-Rate Deserializer with Loop-Through Cable Driver |
| 中文描述： | GS1559的HD - LINX進程，商標第二多速率解串器與環通電纜驅動器 |
| 文件頁數： | 12/74頁 |
| 文件大?。?/td> | 686K |
| 代理商： | GS1559-CBE2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
GS1559 Data Sheet
30572 - 4
July 2005
12 of 74
G4
IOPROC_EN/DIS
Non
Synchronous
Input
CONTROL SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Used to enable or disable I/O processing features.
When set HIGH, the following I/O processing features of the device are
enabled:
EDH CRC Error Correction (SD-only)
ANC Data Checksum Correction
Line-based CRC Error Correction (HD-only)
Line Number Error Correction (HD-only)
TRS Error Correction
Illegal Code Remapping
To enable a subset of these features, keep IOPROC_EN/DIS HIGH and
disable the individual feature(s) in the IOPROC_DISABLE register
accessible via the host interface.
When set LOW, the I/O processing features of the device are disabled,
regardless of whether the features are enabled in the IOPROC_DISABLE
register.
G5
SMPTE_BYPASS
Non
Synchronous
Input /
Output
CONTROL SIGNAL INPUT / STATUS SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
This pin will be an input set by the application layer in slave mode, and will
be an output set by the device in master mode.
Master Mode (MASTER/SLAVE = HIGH)
The SMPTE_BYPASS signal will be HIGH only when the device has
locked to a SMPTE compliant data stream. It will be LOW otherwise.
Slave Mode (MASTER/SLAVE = LOW)
When set HIGH in conjunction with DVB_ASI = LOW, the device will be
configured to operate in SMPTE mode. All I/O processing features may be
enabled in this mode.
When set LOW, the device will not support the descrambling, decoding or
word alignment of received SMPTE data. No I/O processing features will
be available.
G6
RESET_TRST
Non
Synchronous
Input
CONTROL SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Used to reset the internal operating conditions to default settings and to
reset the JTAG test sequence.
Host Mode (JTAG/HOST = LOW)
When asserted LOW, all functional blocks will be set to default conditions
and all input and output signals become high
impedance, including the
serial digital outputs SDO and
SDO.
Must be set HIGH for normal device operation.
NOTE: When in slave mode, reset the device after the SD/
HD
input has
been initially configured, and after each subsequent SD/HD data rate
change.
JTAG Test Mode (JTAG/HOST = HIGH)
When asserted LOW, all functional blocks will be set to default and the
JTAG test sequence will be held in reset.
When set HIGH, normal operation of the JTAG test sequence resumes.
Table 1-1: Pin Descriptions (Continued)
Pin
Number
Name
Timing
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| GS2905 | 500mA CMOS LDO Voltage Regulator |
| GS2905X15 | 500mA CMOS LDO Voltage Regulator |
| GS2905X18 | 500mA CMOS LDO Voltage Regulator |
| GS2905X25 | 500mA CMOS LDO Voltage Regulator |
| GS2905X33 | 500mA CMOS LDO Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS1560 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD-LINX II Voltage Controlled Oscillator |
| GS1560A | 制造商:Gennum Corporation 功能描述: |
| GS1560A_07 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:Dual-Rate Deserializer |
| GS1560A_09 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD-LINX II Dual-Rate Deserializer |
發布緊急采購，3分鐘左右您將得到回復。