- 您現在的位置：買賣IC網 > PDF目錄384325 > GF9331-CBP (Gennum Corporation) DTV/SDTV Motion Co-processor PDF資料下載
參數資料
| 型號： | GF9331-CBP |
| 廠商： | Gennum Corporation |
| 英文描述： | DTV/SDTV Motion Co-processor |
| 中文描述： | 數字電視/標清運動協處理器 |
| 文件頁數： | 25/31頁 |
| 文件大小： | 337K |
| 代理商： | GF9331-CBP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁
GF9331 Data Sheet
Proprietary and Confidential
18303 - 4
June 2004
25 of 31
3.6 Closed Captioning
The GF9331 provides a blanking function for selected input video lines.
Consecutive lines within each input field are blanked, when this function is enabled,
beginning with the CC_BLANK_START_LINE register and ending with the
CC_BLANK_END_LINE register. The blanking is applied prior to any processing
of the video data.
The blanking function is enabled with the CC_BLANK_EN bit.
BLANK_START_LINE and BLANK_END_LINE are each allocated 8-bits within the
host interface.
3.7 RESET
The RESET pin is an active low pin which will reset all internal logic to it's default
conditions when set LOW. On power up it is recommended to reset the device to
ensure all internal registers are set to their default state. When applying a reset, the
GF9331 will load in the STD[4:0] and MODE[2:0] settings from the external pins. If
no further configuration is done, these settings will be used for the operation of the
device.
3.8 Modes of Operation
The device supports enabled and disabled modes of operation. The basic
operating mode for the GF9331 is selected using the MODE pin or the MODE
register within the host interface. See
Table 3-6: Modes of Operation
.
31
15
CMD_RESET
UC
This parameter forces the GF9331 to enter a reset state.
The reset remains in effect until this parameter is cleared
with a subsequent command.
0
15
S
TART_OPERATION
UC
If using external F_IN, V_IN and H_IN signals, this
parameter must be set following the completion of
programming the F_IN, V_IN and H_IN offsets.
0
Table 3-5: Control Register Definitions (Continued)
Address
Bit
Location
Register Name
Class
Description
Default
Table 3-6: Modes of Operation
Mode
Description
0
Disabled
1
Motion processing of input video signal
相關PDF資料 |
PDF描述 |
|---|---|
| GFMM | Ceramic Capacitors Stacks |
| GFMM2505 | Ceramic Capacitors Stacks |
| GFMM2507 | Ceramic Capacitors Stacks |
| GH06510B2A | RED LASER DIODE FOR DVD ROM DRIVE |
| GH30507T2A | GH30507T2A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GF9351A-CBE2 | 制造商:Sigma Designs 功能描述:IC IMAGE PROCESSOR 10BIT DUAL |
| GF9410\5B | 功能描述:MOSFET N-Channel 30V 2A RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| GF9450C-CBE3 | 制造商:Sigma Designs 功能描述:IC VIDEO PROCESSOR 10BIT 701HSBG |
| GF9452A-CBE3 | 制造商:Sigma Designs 功能描述:IC VIDEO PROCESSOR 12BIT 725HSBG |
| GF9926\5B | 功能描述:MOSFET USE 781-SI9926ADY RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。