- 您現在的位置：買賣IC網 > PDF目錄17057 > EVAL-AD7193EBZ (Analog Devices Inc)EVAL BOARD FOR AD7193 PDF資料下載
參數資料
| 型號： | EVAL-AD7193EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 28/57頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR AD7193 |
| 設計資源： | EVAL-AD7193 Schematic AD7193 Gerber Files |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7193 |
| 已供物品： | 板，線纜 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
Data Sheet
AD7193
Rev. D | Page 33 of 56
REFERENCE DETECT
The AD7193 includes on-chip circuitry to detect whether the
part has a valid reference for conversions or calibrations. This
feature is enabled when the REFDET bit in the configuration
register is set to 1. If the voltage between the selected REFINx(+)
and REFINx() pins is less than 0.3 V, the AD7193 detects that
it no longer has a valid reference. In this case, the NOREF bit
of the status register is set to 1. When the voltage between the
selected REFINx(+) and REFINx() pins is greater than 0.6 V,
the AD7193 detects a valid reference so the NOREF bit is set
to 0. The operation of the NOREF bit is undefined when the
voltage between the selected REFINx(+) and REFINx() pins
is between 0.3 V and 0.6 V.
If the AD7193 is performing normal conversions and the NOREF
bit becomes active, the conversion result is all 1s. Therefore, it is
not necessary to continuously monitor the status of the NOREF
bit when performing conversions. It is only necessary to verify
its status if the conversion result read from the ADC data register
is all 1s.
If the AD7193 is performing either an offset or full-scale calibration
and the NOREF bit becomes active, the updating of the respective
calibration registers is inhibited to avoid loading incorrect
coefficients to these registers, and the ERR bit in the status
register is set. If the user is concerned about verifying that a
valid reference is in place every time a calibration is performed,
the status of the ERR bit should be checked at the end of the
calibration cycle.
BIPOLAR/UNIPOLAR CONFIGURATION
The analog input to the AD7193 can accept either unipolar or
bipolar input voltage ranges. A bipolar input range does not
imply that the part can tolerate negative voltages with respect
to system AGND. In pseudo differential mode, signals are
referenced to AINCOM, whereas in differential mode, signals
are referenced to the negative input of the differential pair. For
example, if AINCOM is 2.5 V and the AD7193 AIN1 analog
input is configured for unipolar mode with a gain of 2, the input
voltage range on the AIN1 pin is 2.5 V to 3.75 V when a 2.5 V
reference is used.
If AINCOM is 2.5 V and the AD7193 AIN1 analog input is
configured for bipolar mode with a gain of 2, the analog input
range on AIN1 is 1.25 V to 3.75 V. The bipolar/unipolar option
is chosen by programming the U/B bit in the configuration
register.
DATA OUTPUT CODING
When the ADC is configured for unipolar operation, the output
code is natural (straight) binary with a zero differential input
voltage resulting in a code of 000…000, a midscale voltage resulting
in a code of 100…000, and a full-scale input voltage resulting in
a code of 111…111. The output code for any analog input voltage
can be represented as
Code = (2N × AIN × Gain)/VREF
When the ADC is configured for bipolar operation, the output
code is offset binary with a negative full-scale voltage resulting
in a code of 000…000, a zero differential input voltage resulting
in a code of 100…000, and a positive full-scale input voltage
resulting in a code of 111…111. The output code for any analog
input voltage can be represented as
Code = 2N–1 × [(AIN × Gain/VREF) + 1]
where:
AIN is the analog input voltage.
Gain is the PGA setting (1 to 128).
N = 24.
BURNOUT CURRENTS
The AD7193 contains two 500 nA constant current generators,
one sourcing current from AVDD to AIN(+) and one sinking
current from AIN() to AGND. The currents are switched to
the selected analog input pair. Both currents are either on or off,
depending on the burnout current enable (burn) bit in the
configuration register.
These currents can be used to verify that an external transducer
remains operational before attempting to take measurements on
that channel. After the burnout currents are turned on, they
flow in the external transducer circuit, and a measurement of
the input voltage on the analog input channel can be taken. It
takes some time for the burnout currents to detect an open
circuit condition because the currents must charge any external
capacitors.
There are several reasons that a fault condition is detected: the
front-end sensor may be either open circuit or overloaded, or
the reference may be absent and the NOREF bit in the status
register is set, thus clamping the data to all 1s. The user must
check these three cases before making a determination.
If the voltage measured is 0 V, it may indicate that the transducer
has short circuited. The current sources work over the normal
absolute input voltage range specifications when the analog
inputs are buffered and chop is disabled.
CHANNEL SEQUENCER
The AD7193 includes a channel sequencer, which simplifies
communications with the device in multichannel applications.
The sequencer also optimizes the channel throughput of the
device because the sequencer switches channels at the optimum
rate rather than waiting for instructions via the SPI interface.
Bit CH0 to Bit CH7 in the configuration register are used to enable
the required analog input channels. The analog inputs must be
configured for differential mode or pseudo differential mode
using the pseudo bit in the configuration register. The tempera-
ture sensor is enabled using the TEMP bit in the configuration.
An internal short can also be selected using the short bit in the
configuration register.
相關PDF資料 |
PDF描述 |
|---|---|
| TRK-MPC5634M | TRAK 5634M 144PN R2.1 |
| REF191GSZ | IC VREF SERIES PREC 2.048V 8SOIC |
| DEMO56F8014-EE | BOARD DEMO FOR 56F8014 |
| 0210490222 | CABLE JUMPER 1.25MM .152M 16POS |
| EVAL-AD7795EBZ | BOARD EVAL FOR AD7795 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7194EBZ | 功能描述:EVAL BOARD FOR AD7194 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7195EBZ | 功能描述:BOARD EVAL FOR AD7195 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD7262EDZ | 功能描述:BOARD EVAL CONTROL AD7262 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7264EDZ | 功能描述:BOARD EVALUATION FOR AD7264 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7265CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential/Single-Ended Input, Dual 1 MSPS, 12-Bit, 3-Channel SAR ADC |
發布緊急采購，3分鐘左右您將得到回復。