- 您現在的位置：買賣IC網 > PDF目錄17057 > EVAL-AD7193EBZ (Analog Devices Inc)EVAL BOARD FOR AD7193 PDF資料下載
參數資料
| 型號： | EVAL-AD7193EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 21/57頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR AD7193 |
| 設計資源： | EVAL-AD7193 Schematic AD7193 Gerber Files |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7193 |
| 已供物品： | 板，線纜 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
Data Sheet
AD7193
Rev. D | Page 27 of 56
CONFIGURATION REGISTER
RS2, RS1, RS0 = 010; Power-On/Reset = 0x000117
The configuration register is a 24-bit register from which data
can be read or to which data can be written. This register is
used to configure the ADC for unipolar or bipolar mode, to
enable or disable the buffer, to enable or disable the burnout
currents, to select the gain, and to select the analog input channel.
Table 22 outlines the bit designations for the configuration register.
CON0 through CON23 indicate the bit locations. CON denotes
that the bits are in the configuration register. CON23 denotes
the first bit of the data stream. The number in parentheses
indicates the power-on/reset default status of that bit.
CON23
CON22
CON21
CON20
CON19
CON18
CON17
CON16
Chop(0)
0(0)
REFSEL(0)
0(0)
Pseudo(0)
Short(0)
TEMP(0)
CON15
CON14
CON13
CON12
CON11
CON10
CON9
CON8
CH7(0)
CH6(0)
CH5(0)
CH4(0)
CH3(0)
CH2(0)
CH1(0)
CH0(1)
CON7
CON6
CON5
CON4
CON3
CON2
CON1
CON0
Burn(0)
REFDET(0)
0(0)
BUF(1)
U/B(0)
G2(1)
G1(1)
G0(1)
Table 22. Configuration Register (CON) Bit Designations
Bit Location
Bit Name
Description
CON23
Chop
Chop enable bit.
When the chop bit is cleared, chop is disabled. With chop disabled, higher conversion rates are allowed.
For an FS word of 96 decimal and the sinc4 filter selected, the conversion time is 20 ms and the settling
time is 80 ms. However, at low gains, periodic calibrations may be required to remove the offset and
offset drift.
When the chop bit is set, chop is enabled. When chop is enabled, the offset and offset drift of the ADC
are continuously removed. However, this increases the conversion time and settling time of the ADC.
For example, when FS = 96 decimal and the sinc4 filter is selected, the conversion time with chop
enabled equals 80 ms and the settling time equals 160 ms.
CON22, CON21
0
These bits must be programmed with a Logic 0 for correct operation.
CON20
REFSEL
Reference select bits. The reference source for the ADC is selected using these bits.
REFSEL
Reference Voltage
0
External reference applied between REFIN1(+) and REFIN1().
1
External reference applied between the P1/REFIN2(+) and P0/REFIN2() pins.
CON19
0
This bit must be programmed with a Logic 0 for correct operation.
CON18
Pseudo
Pseudo differential analog inputs. The analog inputs can be configured as differential inputs or pseudo
differential analog inputs. When the pseudo bit is set to 1, the AD7193 is configured to have eight
pseudo differential analog inputs. When pseudo bit is set to 0, the AD7193 is configured to have four
differential analog inputs.
CON17 to CON8
Short, TEMP,
CH7 to CH0
Channel select bits. These bits select which channels are enabled on the AD7193 (see Table 23 and Table 24).
Several channels can be selected, and the AD7193 automatically sequences them. The conversion on
each channel requires the complete settling time. When performing calibrations or when accessing the
calibration registers, only one channel can be selected.
CON7
Burn
When this bit is set to 1, the 500 nA current sources in the signal path are enabled. When burn = 0, the
burnout currents are disabled. The burnout currents can be enabled only when the buffer is active and
when chop is disabled.
CON6
REFDET
Enables the reference detect function. When set, the NOREF bit in the status register indicates when the
external reference being used by the ADC is open circuit or less than 0.6 V maximum. The reference
detect circuitry operates only when the ADC is active.
CON5
0
This bit must be programmed with a Logic 0 for correct operation.
相關PDF資料 |
PDF描述 |
|---|---|
| TRK-MPC5634M | TRAK 5634M 144PN R2.1 |
| REF191GSZ | IC VREF SERIES PREC 2.048V 8SOIC |
| DEMO56F8014-EE | BOARD DEMO FOR 56F8014 |
| 0210490222 | CABLE JUMPER 1.25MM .152M 16POS |
| EVAL-AD7795EBZ | BOARD EVAL FOR AD7795 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7194EBZ | 功能描述:EVAL BOARD FOR AD7194 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7195EBZ | 功能描述:BOARD EVAL FOR AD7195 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD7262EDZ | 功能描述:BOARD EVAL CONTROL AD7262 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7264EDZ | 功能描述:BOARD EVALUATION FOR AD7264 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7265CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential/Single-Ended Input, Dual 1 MSPS, 12-Bit, 3-Channel SAR ADC |
發布緊急采購，3分鐘左右您將得到回復。