參數資料
型號： CLRC632
廠商： NXP Semiconductors N.V.
英文描述： Multiple Protocol Contactless Reader IC
中文描述： 多協議非接觸式讀卡器IC
文件頁數： 104/163頁
文件大小： 948K
代理商： CLRC632
Philips Semiconductors
Product Specification Rev. 3.0; May 2003
Multiple Protocol Contactless Reader IC
CL RC632
104
Confidential
14.3 Putting the Receiver into Operation
In general, the default settings programmed in the Start Up Initialisation File are suitable to use the CL
RC632 for data communication with MIFARE
cards. However, in some environments specific user settings
may achieve better performance.
14.3.1 AUTOMATIC CLOCK-Q CALIBRATION
The quadrature demodulation concept of the receiver generates a phase signal I-clock and a 90°-shifted
quadrature signal Q-clock. To achieve an optimum demodulator performance, the Q- and the
I
-clock have to
have a difference in phase of 90°. After the reset phase of the CL RC632, a calibration procedure is done
automatically. It is possible to have an automatic calibration done at the ending of each Transceive
command. To do so, the
ClkQCalib
bit has to be configured to a value of 0.
Configuring this bit to a constant value of 1 disables all automatic calibrations except the one after the reset
sequence.
It is also possible to initiate one automatic calibration by software. This is done with a 0 to 1 transition of bit
ClkQCalib.
The details:
Note: The duration of the automatic clock Q calibration takes 65 oscillator periods which is approx. 4,8μs.
The value of
ClkQDelay
is proportional to the phase shift between the Q- and the
I
-clock. The status flag
ClkQ180Deg
shows, that the phase shift between the Q- and the
I
-clock is greater than 180°.
Notes:
The start-up configuration file enables an automatically Q-clock calibration after the reset.
While
ClkQCalib
is 1, no automatic calibration is done. Therefore leaving this bit 1 can be used to
permanently disable the automatic calibration.
It is possible to write data to
ClkQDelay
via the μ-Processor. The aim could be a disabling of the
automatic calibration and to pre-set the delay by software. But notice, that configuring the delay value by
software requires that bit
ClkQCalib
has already been set to 1 before and that a time interval of at least
4.8μs has elapsed since then. Each delay value must be written with the
ClkQCalib
bit set to 1. If
ClkQCalib
is 0 the configured delay value will be overwritten by the next interval automatic calibration.
calibration impulse
from reset sequence
a rising edge initiates
a clock Q calibration
calibration impulse
from ending of
TRANSEIVE command
the
ClkQCalib
bit
相關PDF資料
PDF描述
CM-2 Low Cost Miniature Double Balanced Mixer 10-1000 MHz
CM04MC01T COMMON MODE CHOKE COILS (FOR DC AND SIGNAL LINES) SMD TYPE
CM05RC01T COMMON MODE CHOKE COILS (FOR DC AND SIGNAL LINES) SMD TYPE
CM05RC02T CONNECTOR ACCESSORY
CM05RC03T COMMON MODE CHOKE COILS (FOR DC AND SIGNAL LINES) SMD TYPE
相關代理商/技術參數
參數描述
CLRC63201T/0FE 制造商:NXP Semiconductors 功能描述:
CLRC63201T/0FE,112 功能描述:RFID應答器 I.CODE HS READER RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
CLRC63201T/0FE,118 制造商:NXP Semiconductors 功能描述:Interface Misc
CLRC63201T/0FE112 制造商:NXP Semiconductors 功能描述:CNTCLESS RC 5V ISO14443 + ISO15693
CLRC663 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Contactless reader IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*