- 您現在的位置：買賣IC網 > PDF目錄17021 > CDB5530U (Cirrus Logic Inc)BOARD EVAL FOR CS5530 PDF資料下載
參數資料
| 型號： | CDB5530U |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 4/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR CS5530 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 3.84k |
| 數據接口： | 串行 |
| 輸入范圍： | ±2.5 V |
| 在以下條件下的電源（標準）： | 35mW @ 5V |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | CS5530 |
| 已供物品： | 板，CD |
| 相關產品： | CS5530-ISZR-ND - IC ADC 24BIT 1CH W/LNA 20-SSOP 598-1283-5-ND - IC ADC 24BIT 1CH W/LNA 20SSOP 598-1198-5-ND - IC DELTA-SIGMA 24BIT 1CH 20-SSOP |
| 其它名稱： | 598-1158 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
CS5530
12
DS742F3
2.1.1 Analog Input Span
The full-scale input signal that the converter can dig-
itize is a function of the reference voltage connected
between the VREF+ and VREF- pins. The full-scale
input span of the converter is
((VREF+) – (VREF-))/(64Y), where 64 is the gain
of the amplifier and Y is 2 for VRS = 0, or Y is 1 for
VRS = 1. VRS is the Voltage Reference Select bit,
and must be set according to the differential voltage
applied to the VREF+ and VREF- pins on the part.
See section 2.3.4 for more details.
With a 2.5 V reference, the full-scale biploar input
range is equal to ±2.5/64, or about ±39 mV. Note
that these input ranges assume the calibration regis-
ters are set to their default values (i.e. Gain = 1.0 and
Offset = 0.0). The gain setting in the Gain Register
can be altered to map the digital codes of the con-
verter to set full scales from 1 mV to 40 mV.
2.1.2 Voltage Noise Density Performance
Figure 5 illustrates the measured voltage noise den-
sity versus frequency from 0.025 Hz to 10 Hz. The
device was powered with ±2.5 V supplies, using
30 Sps OWR, bipolar mode, and with the input
short bit enabled.
2.1.3 No Offset DAC
An offset DAC was not included in the CS5530 be-
cause the high dynamic range of the converter
eliminates the need for one. The offset register can
be manipulated by the user to mimic the function of
a DAC if desired.
2.2 Overview of ADC Register Structure
and Operating Modes
The CS5530 ADC has an on-chip controller, which
includes a number of user-accessible registers. The
registers are used to hold offset and gain calibration
results, configure the chip's operating modes, hold
conversion instructions, and to store conversion
data words. Figure 6 depicts a block diagram of the
on-chip controller’s internal registers.
The converter has 32-bit registers to function as the
offset and the gain calibration registers. These reg-
isters hold calibration results. The contents of these
registers can be read or written by the user. This al-
lows calibration data to be off-loaded into an exter-
nal EEPROM. The user can also manipulate the
contents of these registers to modify the offset or
the gain slope of the converter.
The converter includes a 32-bit configuration reg-
ister which is used for setting options such as the
power down modes, resetting the converter, short-
ing the analog input, enabling logic outputs, and
other user options.
The following pages document how to initialize the
converter and perform offset and gain calibrations.
Each of the bits of the configuration register is de-
scribed. Also the Command Register Quick Refer-
ence can be used to decode all valid commands (the
first 8-bits into the serial port).
2.2.1 System Initialization
The CS5530 provide no power-on-reset function.
To initialize the ADC, the user must perform a soft-
ware reset via the configuration register. Before
accessing the configuration register, the user must
insure serial port synchronization by using the Se-
rial Port Initialization sequence. This sequence re-
sets the serial port to the command mode and is
accomplished by transmitting at least 15 SYNC1
command bytes (0xFF hexadecimal), followed by
one SYNC0 command (0xFE hexadecimal). Note
that this sequence can be initiated at anytime to
reinitialize the serial port. To complete the system
1
10
100
1000
0.025
0.10
1.00
10.00
Frequency (Hz)
Figure 5. Measured Voltage Noise Density, 64x
相關PDF資料 |
PDF描述 |
|---|---|
| SIP4613ADVP-T1-E3 | IC LOAD SW HISIDE 1A SC75-6 |
| CDB5534U | EVAL BOARD FOR CS5534 |
| AD9648-125EBZ | EVAL BOARD AD9648-125 |
| CDB5463U-Z | EVAL BOARD USB FOR CS5463 |
| AD9633-125EBZ | BOARD EVAL FOR AD9633 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDB5532U | 功能描述:數據轉換 IC 開發工具 Eval Bd 24Bit ADC w/ Ultra Low-Noise USB RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| CDB5534U | 功能描述:數據轉換 IC 開發工具 Eval Bd 24Bit ADC w/ Ultra Low-Noise USB RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| CDB5534U-Z | 功能描述:EVAL BD 24-BIT ADCS W/ULTRALN PG 制造商:cirrus logic inc. 系列:- 零件狀態:在售 A/D 轉換器數:1 位數:24 采樣率（每秒）:3.84k 數據接口:串行 輸入范圍:±2.5 V 不同條件下的功率（典型值）:35mW @ 3.84kSPS 使用的 IC/零件:CS5534 所含物品:板，電纜 標準包裝:1 |
| CDB5540 | 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5540 - Bulk |
| CDB5541 | 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR 5540 & 5541 N/A - Bulk 制造商:Cirrus Logic 功能描述:Tools Development kit For Use |
發布緊急采購，3分鐘左右您將得到回復。