參數資料
型號: CDB5530U
廠商: Cirrus Logic Inc
文件頁數: 21/36頁
文件大?。?/td> 0K
描述: BOARD EVAL FOR CS5530
標準包裝: 1
ADC 的數量: 1
位數: 24
采樣率(每秒): 3.84k
數據接口: 串行
輸入范圍: ±2.5 V
在以下條件下的電源(標準): 35mW @ 5V
工作溫度: -40°C ~ 85°C
已用 IC / 零件: CS5530
已供物品: 板,CD
相關產品: CS5530-ISZR-ND - IC ADC 24BIT 1CH W/LNA 20-SSOP
598-1283-5-ND - IC ADC 24BIT 1CH W/LNA 20SSOP
598-1198-5-ND - IC DELTA-SIGMA 24BIT 1CH 20-SSOP
其它名稱: 598-1158
CS5530
28
DS742F3
2.9 Clock Generator
The CS5530 includes an on-chip inverting amplifi-
er which can be connected with an external crystal
to provide the master clock for the chip. Figure 17
illustrates the on-chip oscillator. It includes loading
capacitors and a feedback resistor to form a Pierce
oscillator configuration. The chips are designed to
operate using a 4.9152 MHz crystal; however, oth-
er crystals with frequencies between 1 MHz to 5
MHz can be used. One lead of the crystal should be
connected to OSC1 and the other to OSC2. Lead
lengths should be minimized to reduce stray capac-
itance. Note that while using the on-chip oscillator,
neither OSC1 or OSC2 is capable of directly driv-
ing any off chip logic. When the on-chip oscillator
is used, the voltage on OSC2 is typically 1/2 V
peak-to-peak. This signal is not compatible with
external logic unless additional external circuitry is
added. The OSC2 output should be used if the on-
chip oscillator output is used to drive other circuit-
ry.
The designer can use an external CMOS compati-
ble oscillator to drive OSC2 with a 1 MHz to 5
MHz clock for the ADC. The external clock into
OSC2 must overdrive the 60 microampere output
of the on-chip amplifier. This will not harm the on-
chip circuitry. In this scheme, OSC1 should be left
unconnected.
2.10 Power Supply Arrangements
The CS5530 is designed to operate from single or
dual analog supplies and a single digital supply.
The following power supply connections are possi-
ble:
VA+ = +5 V; VA- = 0 V; VD+ = +3 V to +5 V
VA+ = +2.5 V; VA- = -2.5 V; VD+ = +3 V to +5 V
VA+ = +3 V; VA- = -3 V; VD+ = +3 V
A VA+ supply of +2.5 V, +3.0 V, or +5.0 V should
be maintained at ±5% tolerance. A VA- supply of
-2.5 V or -3.0 V should be maintained at ±5% tol-
erance. VD+ can extend from +2.7 V to +5.5 V
with the additional restriction that [(VD+) - (VA-)
< 7.5 V].
Figure 18 illustrates the CS5530 connected with a
single +5.0 V supply to measure differential inputs
relative to a common mode of 2.5 V. Figure 19 il-
lustrates the CS5530 connected with ±2.5 V bipolar
analog supplies and a +3 V to +5 V digital supply
to measure ground referenced bipolar signals. Fig-
ures 20 illustrates the CS5532 connected with ±3 V
analog supplies and a +3 V digital supply to mea-
sure ground referenced bipolar signals.
OSC1
MCLK
NOTE: 20 pF capacitors are on chip and
should not be added externally.
1 M
Ω
OSC2
20 pF
+
-
VTH
~
~60 μA
Figure 17. On-chip Oscillator Model
相關PDF資料
PDF描述
SIP4613ADVP-T1-E3 IC LOAD SW HISIDE 1A SC75-6
CDB5534U EVAL BOARD FOR CS5534
AD9648-125EBZ EVAL BOARD AD9648-125
CDB5463U-Z EVAL BOARD USB FOR CS5463
AD9633-125EBZ BOARD EVAL FOR AD9633
相關代理商/技術參數
參數描述
CDB5532U 功能描述:數據轉換 IC 開發工具 Eval Bd 24Bit ADC w/ Ultra Low-Noise USB RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
CDB5534U 功能描述:數據轉換 IC 開發工具 Eval Bd 24Bit ADC w/ Ultra Low-Noise USB RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
CDB5534U-Z 功能描述:EVAL BD 24-BIT ADCS W/ULTRALN PG 制造商:cirrus logic inc. 系列:- 零件狀態:在售 A/D 轉換器數:1 位數:24 采樣率(每秒):3.84k 數據接口:串行 輸入范圍:±2.5 V 不同條件下的功率(典型值):35mW @ 3.84kSPS 使用的 IC/零件:CS5534 所含物品:板,電纜 標準包裝:1
CDB5540 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5540 - Bulk
CDB5541 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR 5540 & 5541 N/A - Bulk 制造商:Cirrus Logic 功能描述:Tools Development kit For Use