參數資料
型號： ADUC7039BCP6Z-RL
廠商： Analog Devices Inc
文件頁數： 85/92頁
文件大?。?/td> 0K
描述： IC MCU ARM7 BATT SENSER 32LFCSP
標準包裝： 2,500
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI
外圍設備： POR，溫度傳感器，WDT
輸入/輸出數： 6
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 1K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 115°C
封裝/外殼： 32-VFQFN 裸露焊盤，CSP
包裝： 帶卷 (TR)
ADuC7039
Data Sheet
Rev. D | Page 86 of 92
Table 61. LINCON MMR Bit Designations
Bits
Description
15 to 13
Reserved.
12
LIN bypass bit.
This bit is set to 1 by user code to take control of the LIN transceiver alone, for LIN conformance test.
This bit is cleared to 0 by user code to operate in normal mode.
11
LIN enable bit.
This bit is set to 1 by user code to enable the LIN interface.
This bit is cleared to 0 by user code to disable the LIN interface or to reset the interface.
10
UART enable bit.
This bit is set by user code to allow transmission without receiving the frame header, for test purposes.
This bit is cleared by user code for normal mode operation.
9
Timing of sync symbol, Bit 0 (not require in a single slave system).
Ensure that if a second break is transmitted it is recognized as such and not timed as part of the sync symbol. If the start
symbol is more than the number of clock ticks dictated by this bit, the device assumes it is now receiving a break and continues
to count the low cycle to see if the break meets the minimum time required for a break as defined in the LINBK MMR.
Set by the user. The first bit of the sync symbol must be less than 750 core clocks (73 s).
This bit is cleared by the user to disable this functionality.
8
Send checksum.
This bit is set by the user to transmit the checksum automatically. This bit must be set after the last data byte to transmit what
is written in LINDAT and after the transmit ready bit is set.
This bit is cleared automatically by hardware when the checksum is sent.
7
Checksum calculation.
This bit is set by the user to calculate automatically a classic checksum (PID excluded).
This bit is cleared by the user to calculate an enhanced checksum (PID included).
Modifying the value of this bit during communication, for example after receiving a PID, resets the checksum.
6
Collision detect and transmit complete interrupt mask.
This bit is set by the user to disable the collision detect and transmit complete interrupt.
This bit is cleared by the user to enable the collision detect and transmit complete interrupt.
When the interrupt is enabled, all occurrences of collision detected causes an interrupt to occur and the collision status bit to
be asserted, regardless of the state of the transmit finished bit. When masking is enabled, once the transmit is finished,
asserted occurrences of collision detected are masked and do not cause an interrupt to occur or the collision detected status
bit to be set. Even if this masking bit has been set by the user if transmit finished has not been asserted by the device, collisions
cause an interrupt to occur and the collision detected status bit to be set.
5
Negative edge maximum error interrupt mask.
This bit is set by the user to disable the negative edge maximum error interrupt.
This bit is cleared by the user to enable the negative edge maximum error interrupt. An interrupt is generated if the negative
edge counter counts more than 57 edges in a frame.
4
Collision detect interrupt mask.
This bit is set by the user to disable the collision detect interrupt.
This bit is cleared by the user to enable the collision detect interrupt.
3
Break received interrupt mask.
This bit is set by the user to disable the break symbol receive interrupt.
This bit is cleared by the user to enable the break symbol receive interrupt.
2
Transmit complete interrupt mask.
This bit is set by the user to disable the transmit complete interrupt.
This bit is cleared by the user to enable the transmit complete interrupt.
1
Transmit ready interrupt mask.
This bit is set by the user to disable the transmit ready interrupt. Set automatically when LINCON[8] is set.
This bit is cleared by the user to enable the transmit ready interrupt.
0
Receive/transmit mode.
This bit is set by user code to transmit data bytes after decoding the PID.
This bit is cleared automatically when a break symbol is received.
相關PDF資料
PDF描述
ADUC7061BCPZ32 IC MCU 16/32BIT 32KB 32LFCSP
ADUC7121BBCZ-RL PRECISION ANALOG MCU I.C
ADUC7122BBCZ-RL PRECISION ANALOG MCU I.C
ADUC7126BSTZ126-RL IC MCU 16/32B 126KB FLASH 80LQFP
ADUC7129BSTZ126 IC DAS MCU ARM7 ADC/DDS 80-LQFP
相關代理商/技術參數
參數描述
ADUC7039WBCPZ 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Trays 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C.
ADUC7039WBCPZ-RL 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C.
ADUC7060 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Precision Analog Microcontroller, Dual Sigma-Delta ADCs, Flash/EE, ARM7TDMI
ADUC7060BCPZ32 功能描述:IC MCU 24BIT 32KB FLASH 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
ADUC7060BCPZ32-RL 功能描述:IC MCU FLASH 24BIT 32KB 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*