- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC7039BCP6Z-RL (Analog Devices Inc)IC MCU ARM7 BATT SENSER 32LFCSP PDF資料下載
參數資料
| 型號： | ADUC7039BCP6Z-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 39/92頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU ARM7 BATT SENSER 32LFCSP |
| 標準包裝： | 2,500 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 連通性： | LIN，SPI |
| 外圍設備： | POR，溫度傳感器，WDT |
| 輸入/輸出數： | 6 |
| 程序存儲器容量： | 64KB（32K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 32 |
| 電壓 - 電源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 數據轉換器： | A/D 2x16b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 115°C |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
ADuC7039
Data Sheet
Rev. D | Page 44 of 92
In ADC low power mode, the ADC, Σ-Δ modulator clock is
no longer driven at 512 kHz but is driven directly from the
on-chip low power (128 kHz) oscillator. Subsequently, for the
same ADCFLT configurations in normal mode, all filter values
should be scaled by a factor of approximately four.
In general, it is possible to program different values of SF and
AF in the ADCFLT register and achieve the same ADC update
rate. In practical terms, the trade off with any value of ADCFLT
is frequency response vs. ADC noise. For optimum filter response
and ADC noise when using combinations of SF and AF, best
practice suggests choosing an SF in the range of 16 decimal to
40 decimal, or 0x10 to 0x28, and then increasing the AF value
to achieve the required ADC throughput. Table 35 shows some
common ADCFLT configurations.
ADC MODES OF OPERATION
The ADCs can be configured into reduced (low power) or
full power (normal) mode of operation by configuring
ADCMDE[3] as appropriate. The ARM7 MCU can also be
configured in low power modes of operation (POWCON[5:3]).
The core power modes are independently controlled and are
not related to the ADC power modes described in this section.
ADC Normal Power Mode
In normal mode, the current and voltage/temperature channels
are fully enabled. The ADC modulator clock is 512 kHz and
enables the ADCs to provide regular conversion results at a
rate of between 10 Hz and 1 kHz (see the ADC Filter Register
section). Both channels are under full control of the MCU and
can be reconfigured at any time. The default ADC update rate
for all channels in this mode is 1.0 kHz.
It is worth emphasizing that I-ADC and V/T-ADC channels can
be configured to initiate periodic, normal power mode, high
accuracy, single conversion cycles before returning to ADC full
power-down mode. This flexibility is facilitated under full MCU
control via the ADCMDE MMR; it ensures that continuous peri-
odic monitoring of battery current, voltage, and temperature
settings is feasible while ensuring the average dc current
consumption is minimized.
In ADC normal mode, the PLL must not be powered down.
ADC Low Power Mode
In ADC low power mode, the I-ADC is enabled in a reduced
power and reduced accuracy configuration. The ADC modu-
lator clock is now driven directly from the on-chip 128 kHz low
power oscillator. The gain of the ADC in this mode is fixed at 512.
All of the ADC peripheral functions (result counter, digital
comparator and accumulator) can be enabled in low power mode.
Typically, in low power mode, the I-ADC only, is configured
to run at a low update rate, continuously monitoring battery
current. The MCU is in power-down mode and wakes up when
the I-ADC interrupts the MCU. This happens after the I-ADC
detects a current conversion beyond a preprogrammed thre-
shold, setpoint, or a set number of conversions.
ADC Comparator and Accumulator
Every I-ADC result can also be compared to a preset threshold
level (ADC0TH) as configured via ADCCFG[3]. An MCU
interrupt is generated if the absolute (sign independent) value
of the ADC result is greater than the preprogrammed com-
parator threshold level.
Finally, a 32-bit accumulator (ADC0ACC) function can be
configured (ADCCFG[5]) allowing the I-ADC to add (or
subtract) multiple I-ADC sample results. User code can read
the accumulated value directly (ADC0ACC) without any
further software processing.
ADC Continuous Interrupt Mode
Setting ADCMDE[5] allows the user to generate an ADC
interrupt after each ADC conversion period, even if the ADC
filter is not fully settled. The corresponding ADC interrupt bit
in the ADCMSKI must also be set to allow the continuous
interrupt. In this mode of operation, ADCSTA[2:0] are used
as valid flags and should not be used to generate interrupts.
Table 35. Common ADCFLT Configurations
ADC Mode
SF
AF
Other Config.
ADCFLT
fADC
tSETTLE
Normal
0x1F
0x16
Chop on
0x961F
10 Hz
0.2 sec
Normal
0x07
0x00
None
0x0007
1 kHz
3 ms
Normal
0x07
0x00
Sinc3 modify
0x0087
1 kHz
3 ms
Low Power
0x10
0x03
Chop on
0x8310
20 Hz
100 ms
Low Power
0x10
0x09
Chop on
0x8910
10 Hz
200 ms
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC7061BCPZ32 | IC MCU 16/32BIT 32KB 32LFCSP |
| ADUC7121BBCZ-RL | PRECISION ANALOG MCU I.C |
| ADUC7122BBCZ-RL | PRECISION ANALOG MCU I.C |
| ADUC7126BSTZ126-RL | IC MCU 16/32B 126KB FLASH 80LQFP |
| ADUC7129BSTZ126 | IC DAS MCU ARM7 ADC/DDS 80-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7039WBCPZ | 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Trays 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C. |
| ADUC7039WBCPZ-RL | 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C. |
| ADUC7060 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Precision Analog Microcontroller, Dual Sigma-Delta ADCs, Flash/EE, ARM7TDMI |
| ADUC7060BCPZ32 | 功能描述:IC MCU 24BIT 32KB FLASH 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| ADUC7060BCPZ32-RL | 功能描述:IC MCU FLASH 24BIT 32KB 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發(fā)布緊急采購，3分鐘左右您將得到回復。