參數資料
型號: AD9995KCPZ
廠商: Analog Devices Inc
文件頁數: 17/60頁
文件大?。?/td> 0K
描述: IC CCD SIGNAL PROCESSOR 56-LFCSP
標準包裝: 1
類型: CCD 信號處理器,12 位
輸入類型: 邏輯
輸出類型: 邏輯
接口: 3 線串口
電流 - 電源: 30mA
安裝類型: 表面貼裝
封裝/外殼: 56-VFQFN 裸露焊盤,CSP
供應商設備封裝: 56-LFCSP-VQ(8x8)
包裝: 托盤
AD9995
–24–
VERTICAL TIMING EXAMPLE
To better understand how the AD9995’s vertical timing generation
is used, consider the example CCD timing chart in Figure 25. This
particular example illustrates a CCD using a general 3-field
readout technique. As described in the Field section, each
readout field should be divided into separate regions to per-
form each step of the readout. The sequence change positions
(SCP) determine the line boundaries for each region, and the
VSEQSEL registers will then assign a particular V-sequence to
each region. The V-sequences will contain the specific timing
information required in each region: V1–V6 pulses (using VPAT
groups), HBLK/CLPOB timing, and VSG patterns for the SG
active lines.
This particular timing example requires four regions for each
of the three fields, labeled Region 0, Region 1, Region 2, and
Region 3. Because the AD9995 allows up to six individual fields
to be programmed, the Field 0, Field 1, and Field 2 registers can
be used to meet the requirements of this timing example. The
four regions for each field are very similar in this example, but
the individual registers for each field allow flexibility to accom-
modate other timing charts.
Region 0 is a high speed vertical shift region. Sweep mode can be
used to generate this timing operation, with the desired number
of high speed vertical pulses needed to clear any charge from the
CCD’s vertical registers.
Region 1 consists of only two lines, and uses standard single line
vertical shift timing.The timing of this region area will be the
same as the timing in Region 3.
Region 2 is the sensor gate line, where the VSG pulses transfer the
image into the vertical CCD registers. This region may require the
use of the second V-pattern group for SG active line.
Region 3 also uses the standard single line vertical shift timing,
the same timing as Region 1.
In summary, four regions are required in each of the three fields.
The timing for Regions 1 and 3 is essentially the same, reducing
the complexity of the register programming.
Other registers will need to be used during the actual readout
operation, such as the MODE register, shutter control registers
(TRIGGER, SUBCK,VSUB, MSHUT, STROBE), and AFE
gain register.These registers will be explained in other examples.
Important Note about Signal Polarities
When programming the AD9995 to generate the V1–V6,
VSG1–VSG5, and SUBCK signals, it is important to note that
the V-driver circuit usually inverts these signals. Carefully check
the required timing signals needed at the input and output of
the V-driver circuit being used and adjust the polarities of the
AD9995’s outputs accordingly.
REV. 0
OBSOLETE
相關PDF資料
PDF描述
ADA4424-6ARUZ IC FILTR VID6CH SD/ED/HD 38TSSOP
ADATE302-02BBCZ IC DCL ATE 500MHZ DUAL 84CSPBGA
ADATE304BBCZ IC DCL ATE 200MHZ DUAL 84CSPBGA
ADATE305BSVZ IC DCL ATE 250MHZ DUAL 100TQFP
ADAU1328BSTZ IC CODEC 24BIT 2ADC/8DAC 48LQFP
相關代理商/技術參數
參數描述
AD9995KCPZRL 功能描述:IC CCD SIGNAL PROCESSOR 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG,串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:20-TSSOP 包裝:管件
AD9995KCPZRL7 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD9996BBCZ 制造商:Rochester Electronics LLC 功能描述:14B 40 MSPS AFETG CONVERTER - Bulk
AD9996BBCZRL 制造商:Rochester Electronics LLC 功能描述:- Bulk
AD-9FT4-B2 制造商:Pan Pacific 功能描述: