- 您現在的位置：買賣IC網 > PDF目錄1895 > AD9992BBCZRL (Analog Devices Inc)IC CCD SGNL PROC 12BIT 105CSPBGA PDF資料下載
參數資料
| 型號： | AD9992BBCZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 60/92頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CCD SGNL PROC 12BIT 105CSPBGA |
| 產品變化通告： | AD9992 Discontinuation 22/Feb/2012 |
| 標準包裝： | 2,000 |
| 類型： | CCD 信號處理器，12 位 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | 3 線串口 |
| 電流 - 電源： | 27mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 105-LFBGA，CSPBGA |
| 供應商設備封裝： | 105-CSPBGA（8x8） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
AD9992
Rev. C | Page 63 of 92
Variable Gain Amplifier
The VGA stage provides a gain range of approximately 6 dB to
42 dB, programmable with 10-bit resolution through the serial
digital interface. A gain of 6 dB is needed to match a 1 V input
signal with the ADC full-scale range of 2 V. When compared to
1 V full-scale systems, the equivalent gain range is 0 dB to 36 dB.
The VGA gain curve follows a linear-in-dB characteristic. The
exact VGA gain is calculated for any gain register value by
Gain (dB) = (0.0358 × Code) + 5.75
where Code is the range of 0 to 1023.
VGA GAIN REGISTER CODE
V
G
A
GA
IN
(
d
B
)
42
36
30
24
18
12
6
0
127
255
383
511
639
767
895
1023
05
89
1-
0
6
8
Figure 73. VGA Gain Curve
ADC
The AD9992 uses a high performance ADC architecture
optimized for high speed and low power. Differential non-
linearity (DNL) performance is typically better than 0.5 LSB.
typical linearity and noise performance plots for the AD9992.
Optical Black Clamp
The optical black clamp loop is used to remove residual offsets in
the signal chain and to track low frequency variations in the CCD’s
black level. During the optical black (shielded) pixel interval on
each line, the ADC output is compared with a fixed black level
reference, selected by the user in the clamp level register. The value
can be programmed between 0 LSB and 255 LSB in 1023 steps.
The resulting error signal is filtered to reduce noise; the correction
value is applied to the ADC input through a DAC. Normally,
the optical black clamp loop is turned on once per horizontal
line, but this loop can be updated more slowly to suit a particular
application. If external digital clamping is used during post-
processing, the AD9992 optical black clamping can be disabled
using Bit D2 in the AFE Register Address 0x00. When the loop is
disabled, the clamp level register can still be used to provide
fixed offset adjustment.
If the CLPOB loop is disabled, higher VGA gain settings reduce
the dynamic range because the uncorrected offset in the signal
path is amplified.
The CLPOB pulse should be aligned with the CCD’s optical
black pixels. It is recommended that the CLPOB pulse duration
be at least 20 pixels wide. Shorter pulse widths can be used, but
the ability for the loop to track low frequency variations in the
black level will be reduced. See the Horizontal Clamping and
Blanking section for timing examples.
Digital Data Outputs
The AD9992 digital output data is latched using the rising edge
of the DOUTPHASE register value, as shown in Figure 72.
also possible to leave the output latches transparent so that the data
outputs are valid immediately from the ADC. Programming the
AFE Register Address 0x01, Bit D1, to 1 sets the output latches to
transparent. The data outputs can also be disabled (three-stated) by
setting the AFE Register Address 0x01, Bit D0, to 1.
The DCLK output can be used for external latching of the data
outputs. By default, the DCLK output tracks the values of the
DOUTPHASE registers. By changing the DCLKMODE register,
the DCLK output can be held at a fixed phase, and DOUTPHASE
register values are ignored. The DCLK output can also be inverted
with respect to DOUT, using the DCLKINV register bit.
The switching of the data outputs can couple noise back into
the analog signal path. To minimize switching noise, it is
recommended that the DOUTPHASE registers be set to the same
edge as the SHP sampling location, or up to 15 edges after the SHP
sampling location. Other settings can produce good results, but
experimentation is necessary. It is recommended that the
DOUTPHASE location not occur between the SHD sampling
location and 15 edges after the SHD location. For example, if
SHDLOC = 0, DOUTPHASE should be set to an edge location
of 16 or greater. If adjustable phase is not required for the data
outputs, the output latch can be left transparent by using
Address 0x01, Bit D1.
The data output coding is normally straight binary, but the coding
can be changed to gray coding by setting the AFE Register
Address 0x01, Bit D2, to 1.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9995KCPZ | IC CCD SIGNAL PROCESSOR 56-LFCSP |
| ADA4424-6ARUZ | IC FILTR VID6CH SD/ED/HD 38TSSOP |
| ADATE302-02BBCZ | IC DCL ATE 500MHZ DUAL 84CSPBGA |
| ADATE304BBCZ | IC DCL ATE 200MHZ DUAL 84CSPBGA |
| ADATE305BSVZ | IC DCL ATE 250MHZ DUAL 100TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9993BBCZ | 功能描述:IC MIXED-SIGNAL FRONT END 196BGA 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 類型:ADC，DAC 輸入類型:LVDS 輸出類型:LVDS 接口:SPI 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:196-LFBGA，CSPBGA 供應商器件封裝:196-CSPBGA（12x12） 標準包裝:1 |
| AD9993BBCZRL | 功能描述:IC MIXED-SIGNAL FRONT END 196BGA 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:在售 類型:ADC，DAC 輸入類型:LVDS 輸出類型:LVDS 接口:SPI 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:196-LFBGA，CSPBGA 供應商器件封裝:196-CSPBGA（12x12） 標準包裝:1,500 |
| AD9993-EBZ | 功能描述:EVAL BOARD MXFE AD9993 制造商:analog devices inc. 系列:* 零件狀態:在售 標準包裝:1 |
| AD9994 | 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit CCD Signal Processor with Precision Timing Generator |
| AD9994BCP | 制造商:Analog Devices 功能描述:AFE GEN PURPOSE 12-BIT 64LFCSP - Bulk |
發布緊急采購，3分鐘左右您將得到回復。