參數資料
型號： 7641
英文描述： 7641 Group Datasheet Datasheet 2145K/MAR.26.02
中文描述： 7641組數據表數據表2145K/MAR.26.02
文件頁數： 45/137頁
文件大小： 2145K
代理商： 7641
44
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
USB Transmission
Endpoint 0 to Endpoint 4 have IN (transmit) FIFOs individually.
Each endpoint
’
s FIFO is configured in following way:
Endpoint 0: 16-byte
Endpoint 1: Mode 0: 512-byte
Mode 1: 1024-byte
Mode 2: 0-byte
Mode 3: 2048-byte
Mode 4: 768-byte
Mode 5: 880-byte
Endpoint 2: Mode 0: 32-byte
Mode 1: 128-byte
Endpoint 3: 16-byte
Endpoint 4: 16-byte
When Endpoint 1 or Endpoint 2 is used for data transmit, the IN
FIFO size can be selected. Endpoint 1 and Endpoint 2 have pro-
grammable IN-FIFOs size; 6 modes for Endpoint 1, and 2 modes
for Endpoint 2. Each mode can be selected by the USB endpoint
FIFO mode selection register (address 005F
16
).
When writing data to the USB Endpoint-x FIFO (addresses 0060
16
to 0064
16
) in the SFR area, the internal write pointer for the IN
FIFO is automatically increased by 1. When the AUTO_SET bit is
“
1
”
and if the stored data reaches to the max. packet value set in
USB Endpoint x IN max. packet size register (address 005B
16
),
the USB FCU sets the IN_PKT_RDY bit to
“
1
”
. When the
AUTO_SET bit is
“
0
”
, the IN_PKT_RDY bit will not be automati-
cally set to
“
1
”
; it must be set to
“
1
”
by software. (The AUTO_SET
bit function is not applicable to Endpoint 0.)
The USB FCU transmits the data when it receives the next IN to-
ken. The IN_PKT_RDY bit automatically goes to
“
0
”
when the data
transfer is complete.
G
Isochronous transfer
Endpoints 1 to 4 can be used in isochronous transfer mode. When
using isochronous transfer mode, the ISO/TOGGLE_INIT bit must
be set to
“
1
”
. When ISO_UPDATE =
“
1
”
and the corresponding
endpoint
’
s ISO/TOGGLE_INIT bit =
“
1
”
, the USB FCU delays the
rise of the IN_PKT_RDY bit until the next SOF signal transmis-
sion. In this way, the USB FCU can synchronize a transmit data to
the SOF signal.
G
Interrupt transfer mode
Endpoints 1 to 4 can be used in interrupt transfer mode. During a
regular interrupt transfer, an interrupt transaction is similar to the
bulk transfer. Therefore, there is no special setting required. When
IN-endpoint is used for a rate feedback interrupt transfer, INTPT
bit of the IN_CSR register must be set to
“
1
”
. The following steps
show how to configure the IN-endpoint for the rate feedback inter-
rupt transfer.
1. Set a value which is larger than 1/2 of the USB Endpoint-x FIFO
size to the USB Endpoint x IN max. package size register.
2. Set INTPT bit to
“
1
”
.
3. Flush the old data in the FIFO.
4. Store transmission data to the IN FIFO and set the
IN_PKT_RDY bit to
“
1
”
.
5. Repeat steps 3 and 4.
In a real application, the function-side always has transfer data
when the function sends an endpoint in a rate feedback interrupt.
Accordingly, the USB FCU never returns a NAK against the host
IN token for the rate feedback interrupt. The USB FCU always
transmits data in the FIFO in response to an IN token, regardless
of IN_PKT_RDY. However, this premises that there is always an
ACK response from Host PC after the 7641 Group has transmitted
data to IN token.
When MAXP size
≤
(a half of IN FIFO size), the IN FIFO can store
two packets (called double buffer). At this time, the IN FIFO sta-
tus can be checked by monitoring the IN_PKT_RDY bit and the
TX_NOT_EPT flag. The TX_NOT_EPT flag is a read-only flag
which shows the FIFO state. When IN_PKY_RDY = 0 and
TX_NOT_EPT = 0, IN FIFO is empty. When IN_PKY_RDY = 0 and
TX_NOT_EPT = 1, IN FIFO has one packet.
In double buffer mode, as long as the IN FIFO is not filled with
double packets, IN_PKT_RDY will not be set to
“
1
”
, even if it is set
to
“
1
”
by software, but TX_NOT_EPT flag will be set to
“
1
”
. In
single buffer mode, if MAXP > (a half of IN FIFO), this condition
never occurs.
When IN_PKT_RDY =
“
1
”
and TX_NOT_EPT =
“
1
”
, IN FIFO holds
two packets in double buffer mode and one packet in single
packet mode. In single packet mode, when the IN_PKT_RDY bit is
set to
“
1
”
by software, the TX_NOT_EPT flag is set to
“
1
”
as well.
During double buffer mode, if you want to load two packets se-
quentially, you must set the IN_PKT_RDY bit to
“
1
”
each time a
packet is loaded.
相關PDF資料
PDF描述
7643 IrDA. protocol handler plus endec for DCE Apps, -40C to +85C, 18-SOIC 300mil, TUBE
765-11-(SERIES) Analog IC
765-11-20K Analog IC
765-11-25A Analog IC
765-11E 8 BIT INPUT/OUTPUT EXPANDER, I2C INTERFACE, -40C to +125C, 20-QFN, TUBE
相關代理商/技術參數
參數描述
764-1"x36yd-Black 功能描述:膠帶 BLACK 1X36YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Blue 功能描述:膠帶 764 BLUE 1X36YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Green 功能描述:膠帶 GREEN 1X36YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Orange 功能描述:膠帶 764 ORANGE 1X36 YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Red 功能描述:膠帶 764 RED 1X36 YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*