參數資料
型號： 7641
英文描述： 7641 Group Datasheet Datasheet 2145K/MAR.26.02
中文描述： 7641組數據表數據表2145K/MAR.26.02
文件頁數： 21/137頁
文件大?。?/td> 2145K
代理商： 7641
20
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
7641 Group
INTERRUPTS
There are twenty-four interrupt sources: five externals, eighteen
internals, and one software.
Interrupt Control
Each interrupt except the BRK instruction interrupt has both an Inter-
rupt Request Bit and an Interrupt Enable Bit, and is controlled by the
Interrupt Disable Flag (I). An interrupt occurs if the corresponding
Interrupt Request and Enable Bits are
“
1
”
and the Interrupt Disable
Flag is
“
0
”
.
Interrupt Enable Bits can be set or cleared by software. Interrupt Re-
quest Bits can be cleared by software, but cannot be set by software.
Additionally, an active edge of INT
1
and INT
2
can be selected by
using the interrupt edge select register (address 0011
16
); an active
edge of CNTR
0
can be done by using the timer X mode register
(address 0027
16
); an active edge of CNTR
1
can be done by using
the timer Y mode register (address 0028
16
).
The BRK instruction interrupt and reset cannot be disabled with any
flag or bit. The I Flag disables all interrupts except the BRK instruc-
tion interrupt and reset. If several interrupts requests occur at the
same time, the interrupt with the highest priority is accepted first.
Interrupt Operation
When an interrupt request occurs, the following operations are auto-
matically performed:
1.The processing being executed is stopped.
2.The contents of the program counter and processor status reg-
ister are automatically pushed onto the stack.
3.The Interrupt Disable Flag is set and the corresponding in-
terrupt request bit is cleared.
4.The interrupt jump destination address is read from the vector
table into the program counter.
I
Notes
When setting the followings, the interrupt request bit may be set to
“
1
”
.
When setting external interrupt active edge
Related register: Interrupt polarity select register (address 0011
16
)
Timer X mode register (address 0027
16
)
Timer Y mode register (address 0028
16
)
When not requiring for the interrupt occurrence synchronized with
these setting, take the following sequence.
Set the corresponding Interrupt Enable Bit to
“
0
”
(disabled).
Set the Interrupt Edge Select Bit (Active Edge Switch Bit).
Set the corresponding Interrupt Request Bit to
“
0
”
after 1 or more
instructions have been executed.
Set the corresponding Interrupt Enable Bit to
“
1
”
(enabled).
Fig. 16 Interrupt control
I
n
I
t
e
t
r
r
r
u
r
p
u
t
t
r
e
e
q
n
u
a
e
b
s
l
e
t
b
b
i
i
t
t
n
e
p
I
n
t
e
r
r
u
p
t
d
i
s
a
b
l
e
f
l
a
g
(
I
)
BRK instruction
Reset
Interrupt request
相關PDF資料
PDF描述
7643 IrDA. protocol handler plus endec for DCE Apps, -40C to +85C, 18-SOIC 300mil, TUBE
765-11-(SERIES) Analog IC
765-11-20K Analog IC
765-11-25A Analog IC
765-11E 8 BIT INPUT/OUTPUT EXPANDER, I2C INTERFACE, -40C to +125C, 20-QFN, TUBE
相關代理商/技術參數
參數描述
764-1"x36yd-Black 功能描述:膠帶 BLACK 1X36YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Blue 功能描述:膠帶 764 BLUE 1X36YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Green 功能描述:膠帶 GREEN 1X36YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Orange 功能描述:膠帶 764 ORANGE 1X36 YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Red 功能描述:膠帶 764 RED 1X36 YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*