參數資料
型號: 7641
英文描述: 7641 Group Datasheet Datasheet 2145K/MAR.26.02
中文描述: 7641組數據表數據表2145K/MAR.26.02
文件頁數: 11/137頁
文件大?。?/td> 2145K
代理商: 7641
10
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
7641 Group
[Processor status register (PS)]
The processor status register is an 8-bit register consisting of 5 flags
which indicate the status of the processor after an arithmetic opera-
tion and 3 flags which decide MCU operation. Branch operations can
be performed by testing the Carry (C) flag , Zero (Z) flag, Overflow
(V) flag, or the Negative (N) flag. In decimal mode, the Z, V, N flags
are not valid.
Bit 0: Carry flag (C)
The C flag contains a carry or borrow generated by the arithmetic
logic unit (ALU) immediately after an arithmetic operation. It can
also be changed by a shift or rotate instruction.
Bit 1: Zero flag (Z)
The Z flag is set if the result of an immediate arithmetic operation
or a data transfer is
0
, and cleared if the result is anything other
than
0
.
Bit 2: Interrupt disable flag (I)
The I flag disables all interrupts except for the interrupt
generated by the BRK instruction.
Interrupts are disabled when the I flag is
1
.
Bit 3: Decimal mode flag (D)
The D flag determines whether additions and subtractions are
executed in binary or decimal. Binary arithmetic is executed when
this flag is
0
; decimal arithmetic is executed when it is
1
.
Decimal correction is automatic in decimal mode. Only the ADC
Bit 4: Break flag (B)
The B flag is used to indicate that the current interrupt was
generated by the BRK instruction. The BRK flag in the processor
status register is always
0
. When the BRK instruction is used to
generate an interrupt, the processor status register is pushed
onto the stack with the break flag set to
1
.
Bit 5: Index X mode flag (T)
When the T flag is
0
, arithmetic operations are performed
between accumulator and memory. When the T flag is
1
, direct
arithmetic operations and direct data transfers are enabled
between memory locations.
Bit 6: Overflow flag (V)
The V flag is used during the addition or subtraction of one byte
of signed data. It is set if the result exceeds +127 to -128. When
the BIT instruction is executed, bit 6 of the memory location
operated on by the BIT instruction is stored in the overflow flag.
Bit 7: Negative flag (N)
The N flag is set if the result of an arithmetic operation or data
transfer is negative. When the BIT instruction is executed, bit 7 of
the memory location operated on by the BIT instruction is stored
in the negative flag.
Table 5 Set and clear instructions of each bit of processor status register
C flag
SEC
CLC
Set instruction
Clear instruction
Z flag
I flag
SEI
CLI
D flag
SED
CLD
B flag
T flag
SET
CLT
V flag
CLV
N flag
相關PDF資料
PDF描述
7643 IrDA. protocol handler plus endec for DCE Apps, -40C to +85C, 18-SOIC 300mil, TUBE
765-11-(SERIES) Analog IC
765-11-20K Analog IC
765-11-25A Analog IC
765-11E 8 BIT INPUT/OUTPUT EXPANDER, I2C INTERFACE, -40C to +125C, 20-QFN, TUBE
相關代理商/技術參數
參數描述
764-1"x36yd-Black 功能描述:膠帶 BLACK 1X36YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Blue 功能描述:膠帶 764 BLUE 1X36YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Green 功能描述:膠帶 GREEN 1X36YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Orange 功能描述:膠帶 764 ORANGE 1X36 YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds
764-1"x36yd-Red 功能描述:膠帶 764 RED 1X36 YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds