- 您現在的位置：買賣IC網 > PDF目錄376463 > XRT83VSH38IB (EXAR CORP) 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT83VSH38IB |
| 廠商： | EXAR CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| 中文描述： | DATACOM, PCM TRANSCEIVER, PBGA225 |
| 封裝： | 19 X 19 MM, 1 MM PITCH, PLASTIC, BGA-225 |
| 文件頁數： | 46/76頁 |
| 文件大小： | 722K |
| 代理商： | XRT83VSH38IB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
XRT83VSH38
43
8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
REV. 1.0.7
6.3
The Microprocessor Interface Block Signals
The LIU may be configured into different operating modes and have its performance monitored by software
through a standard microprocessor using data, address and control signals. These interface signals are
described below in
Table 14
,
Table 15
, and
Table 16
. The microprocessor interface can be configured to
operate in Intel mode or Motorola mode. When the microprocessor interface is operating in Intel mode, some
of the control signals function in a manner required by the Intel 80xx family of microprocessors. Likewise, when
the microprocessor interface is operating in Motorola mode, then these control signals function in a manner as
required by the Motorola microprocessors. (For using a Motorola 68K asynchronous processor, see
Figure 36
and
Table 18
)
Table 14
lists and describes those microprocessor interface signals whose role is
constant across the two modes.
Table 15
describes the role of some of these signals when the microprocessor
interface is operating in the Intel mode. Likewise,
Table 16
describes the role of these signals when the
microprocessor interface is operating in the Motorola Power PC mode.
T
ABLE
14: XRT83VSH38 M
ICROPROCESSOR
I
NTERFACE
S
IGNALS
THAT
EXHIBIT
CONSTANT
ROLES
IN
BOTH
I
NTEL
AND
M
OTOROLA
M
ODES
P
IN
N
AME
T
YPE
D
ESCRIPTION
μ
PTS[2:1]
I
Microprocessor Interface Mode Select Input pins
These two pins are used to specify the microprocessor interface mode. The relationship
between the state of these two input pins, and the corresponding microprocessor mode is pre-
sented in
Table 13
.
DATA[7:0]
I/O
Bi-Directional Data Bus for register "Read" or "Write" Operations.
ADDR[7:0]
I
Eight-Bit Address Bus Inputs
The XRT83VSH38 LIU microprocessor interface uses a direct address bus. This address bus
is provided to permit the user to select an on-chip register for Read/Write access.
CS
I
Chip Select Input
This active low signal selects the microprocessor interface of the XRT83VSH38 LIU and
enables Read/Write operations with the on-chip register locations.
T
ABLE
15: I
NTEL
MODE
: M
ICROPROCESSOR
I
NTERFACE
S
IGNALS
XRT83VSH38
P
IN
N
AME
I
NTEL
E
QUIVALENT
P
IN
T
YPE
D
ESCRIPTION
ALE
ALE
I
Address-Latch Enable:
This active high signal is used to latch the contents on
the address bus ADDR[7:0]. The contents of the address bus are latched into the
ADDR[7:0] inputs on the falling edge of ALE.
RD_DS
RD
I
Read Signal:
This active low input functions as the read signal from the local
μ
P.
When this pin is pulled “Low” (if CS is “Low”) the LIU is informed that a read oper-
ation has been requested and begins the process of the read cycle.
WR_R/W
WR
I
Write Signal:
This active low input functions as the write signal from the local
μ
P.
When this pin is pulled “Low” (if CS is “Low”) the LIU is informed that a write
operation has been requested and begins the process of the write cycle.
RDY
RDY
O
Ready Output:
This active low signal is provided by the LIU device. It indicates
that the current read or write cycle is complete, and the LIU is waiting for the next
command.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT84L14 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| XRT84L18 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| XRT84L38 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| XRT84L38_06 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| XRT84L38IB | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83VSH38IB-F | 功能描述:外圍驅動器與原件 - PCI 8 Channel Short-Haul RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83VSH38IB-F | 制造商:Exar Corporation 功能描述:T1/E1 LIU IC |
| XRT84L38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER |
| XRT84L38_06 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER |
| XRT84L38IB | 功能描述:網絡控制器與處理器 IC 8 Ch T1/E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。