參數資料
型號： XRT83VSH38IB
廠商： EXAR CORP
元件分類： 數字傳輸電路
英文描述： 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
中文描述： DATACOM, PCM TRANSCEIVER, PBGA225
封裝： 19 X 19 MM, 1 MM PITCH, PLASTIC, BGA-225
文件頁數： 12/76頁
文件大小： 722K
代理商： XRT83VSH38IB
XRT83VSH38
9
8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
REV. 1.0.7
PARALLEL MICROPROCESSOR INTERFACE
S
IGNAL
N
AME
BGA
L
EAD
#
T
YPE
D
ESCRIPTION
HW/HOST
T10
I
Mode Control Input
This pin is used to select Host mode or Hardware mode. By default, the LIU is set in
Hardware mode. To use Host mode, this pin must be pulled "Low".
N
OTE
:
Internally pulled “High” with a 50k
resistor.
WR_R/W/EQC0
D7
I
Write Input(R/W)/Equalizer Control Signal 0
Host Mode
This pin is used to communicate a Read or Write operation according to the which
microprocessor is chosen. See the Microprocessor Section of this datasheet for
details.
Hardware Mode
EQC[4:0] are used to set the Receiver Gain, Receiver Impedance and the Transmit
Line Build Out. See
Table 22
for more details.
N
OTE
:
Internally pulled “Low” with a 50k
resistor.
RD_DS/EQC1
C7
I
Read Input (Data Strobe)/Equalizer Control Signal 1
Host Mode
This pin is used to communicate a Read or Write operation according to the which
microprocessor is chosen. See the Microprocessor Section of this datasheet for
details.
Hardware Mode
EQC[4:0] are used to set the Receiver Gain, Receiver Impedance and the Transmit
Line Build Out. See
Table 22
for more details.
N
OTE
:
Internally pulled “Low” with a 50k
resistor.
ALE/EQC2
A7
I
Address Latch Input (Address Strobe)
Host Mode
This pin is used to latch the address contents into the internal registers within the LIU
device. See the Microprocessor Section of this datasheet for details.
Hardware Mode
EQC[4:0] are used to set the Receiver Gain, Receiver Impedance and the Transmit
Line Build Out. See
Table 22
for more details.
N
OTE
:
Internally pulled “Low” with a 50k
resistor.
CS/EQC3
B7
I
Chip Select Input - Host mode:
Host Mode
This pin is used to initiate communication with the microprocessor interface. See the
Microprocessor Section of this datasheet for details.
Hardware Mode
EQC[4:0] are used to set the Receiver Gain, Receiver Impedance and the Transmit
Line Build Out. See
Table 22
for more details.
N
OTE
:
Internally pulled “Low” with a 50k
resistor.
相關PDF資料
PDF描述
XRT84L14 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT84L18 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT84L38 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT84L38_06 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
XRT84L38IB Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
相關代理商/技術參數
參數描述
XRT83VSH38IB-F 功能描述:外圍驅動器與原件 - PCI 8 Channel Short-Haul RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83VSH38IB-F 制造商:Exar Corporation 功能描述:T1/E1 LIU IC
XRT84L38 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER
XRT84L38_06 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER
XRT84L38IB 功能描述:網絡控制器與處理器 IC 8 Ch T1/E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*