參數資料
型號： XRT73L03BIV
廠商： Exar Corporation
文件頁數： 47/61頁
文件大小： 0K
描述： IC LIU E3/DS3/STS-1 3CH 120LQFP
標準包裝： 72
類型： 線路接口裝置（LIU）
驅動器/接收器數： 3/3
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 120-LQFP
供應商設備封裝： 120-LQFP（14x20）
包裝： 托盤
XRT73L03B
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 1.0.1
49
To configure Channel (n) to operate in the Digital Lo-
cal Loop-Back Mode, pull both the LLB input pin and
the RLB input pin "High".
4.3
THE REMOTE LOOP-BACK MODE
When a given channel is configured to operate in the
Remote Loop-Back Mode, the channel ignores any
signals that are input to the TPData and TNData input
pins. The channel receives the incoming line signal
via the RTIP and RRing input pins. This data is pro-
cessed through the entire Receive Section and is out-
put to the Receive Terminal Equipment via the RPOS,
RNEG and RxClk output pins. Additionally, this data
is also internally looped back into the Pulse-Shaping
block within the Transmit Section. At this point, this
data is routed through the remainder of the Transmit
Section of the channel and transmitted out onto the
line via the TTIP_(n) and TRing_(n) output pins.
Figure 35 illustrates the path that the data takes when
the chip is configured to operate in the Remote Loop-
Back Mode.
Configure a channel to operate in the Remote Loop-
Back Mode by employing either one of the following
two steps
a. Operating in the HOST Mode
To configure Channel (n) to operate in the Remote
Loop-Back Mode, write a "1" into the RLB bit-field,
and a "0" into the LLB bit-field, within Command Reg-
ister CR4.
b. Operating in the Hardware Mode
To configure Channel(n) to operate in the Remote
Loop-Back Mode, pull both the RLB_(n) input pin to
“High" and the LLB_(n) input pin to "Low".
FIGURE 35. THE REMOTE LOOP-BACK PATH, WITHIN A GIVEN CHANNEL
AGC/
Equalizer
Peak
Detector
LOS Detector
Slicer
Clock
Recovery
Data
Recovery
Invert
Loop MUX
HDB3/
B3ZS
Decoder
LOSTHR_(n)
SDI
SDO
SClk
CS
REGR
RTIP_(n)
RRing_(n)
REQEN_(n)
RxClk_(n)
RPOS_(n)
RNEG_(n)
LCV_(n)
ENDECDIS
RLOS_(n)
LLB_(n)
RLB_(n)
TAOS_(n)
TPData_(n)
TNData_(n)
TxClk_(n)
Notes: 1. (n) = 0, 1 or 2 for respective Channels
2. Serial Processor Interface input pins are shared by the three Channels in HOST Mode and redefined in
Hardware Mode.
RLOL_(n) EXClk_(n)
Device
Monitor
MTIP_(n)
MRing_(n)
Transmit
Logic
Duty Cycle Adjust
TxLEV_(n)
TxOFF_(n)
DMO_(n)
TTIP_(n)
TRing_(n)
Pulse
Shaping
HDB3/
B3ZS
Encoder
Serial
Processor
Interface
Remote
Loop-Back Path
COMMAND REGISTER CR4-(n)
D4
D3
D2
D1
D0
X
STS-1/DS3_(n)
E3_(n)
LLB_(n)
RLB_(n)
XX
X
0
1
相關PDF資料
PDF描述
IDT72825LB15PF IC FIFO SYNC DL 1024X18 128TQFP
MS27472T12F35P CONN RCPT 22POS WALL MNT W/PINS
IDT72V3650L6PFG8 IC FIFO SS 2048X36 6NS 128-TQFP
MS3100A28-2P CONN RCPT 14POS WALL MNT W/PINS
MS27473E10F35SA CONN PLUG 13POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
XRT73L03BIV-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73L03IV 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL E3/DS3/STS-1 LINE INTERFCE UNIT
XRT73L03IVS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
XRT73L04A 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73L04AIV 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*