- 您現在的位置：買賣IC網 > PDF目錄245698 > W25Q64BVZEIP (WINBOND ELECTRONICS CORP) 8M X 8 SPI BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | W25Q64BVZEIP |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 8M X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 8 X 6 MM, GREEN, WSON-8 |
| 文件頁數： | 42/61頁 |
| 文件大?。?/td> | 1726K |
| 代理商： | W25Q64BVZEIP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
W25Q64BV
Publication Release Date: July 08, 2010
- 47 -
Revision E
11.2.29 Continuous Read Mode Reset (FFh or FFFFh)
For Fast Read Dual/Quad I/O operations, “Continuous Read Mode” Bits (M7-0) are implemented to
further reduce instruction overhead. By setting the (M7-0) to “Ax” hex, the next Fast Read Dual/Quad I/O
operation does not require the BBh/EBh instruction code (See 11.2.12 Fast Read Dual I/O and 11.2.13
Fast Read Quad I/O for detail descriptions).
If the system controller is Reset during operation it will likely send a standard SPI instruction, such
as Read ID (9Fh) or Fast Read (0Bh), to the W25Q64BV. However, as with most SPI Serial Flash
memories, the W25Q64BV does not have a hardware Reset pin, so if Continuous Read Mode bits are set
to “Ax” hex, the W25Q64BV will not recognize any standard SPI instructions. To address this possibility, it
is recommended to issue a Continuous Read Mode Reset instruction as the first instruction after a
system Reset. Doing so will release the Continuous Read Mode from the “Ax” hex state and allow
Standard SPI instructions to be recognized. The Continuous Read Mode Reset instruction is shown in
figure 30.
/CS
Mode Bit Reset
for Dual I/O
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
Mode Bit Reset
for Quad I/O
FFh
Don’t Care
CLK
IO
0
IO
1
IO
2
/CS
Mode Bit Reset
for Dual I/O
Mode 3
Mode 0
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Mode 3
Mode 0
Mode Bit Reset
for Quad I/O
FFh
Don’t Care
IO
3
Don’t Care
IO
3
CLK
IO
0
IO
1
IO
2
Figure 30. Continuous Read Mode Reset for Fast Read Dual/Quad I/O
To reset “Continuous Read Mode” during Quad I/O operation, only eight clocks are needed. The
instruction is “FFh”. To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are
needed to shift in instruction “FFFFh”.
相關PDF資料 |
PDF描述 |
|---|---|
| W3DG634V7D2 | 4M X 64 SYNCHRONOUS DRAM MODULE, DMA168 |
| WPF512K8C70TFI5 | 512K X 8 FLASH 5V PROM, 70 ns, PDSO32 |
| WPF512K8C90TRM5 | 512K X 8 FLASH 5V PROM, 90 ns, PDSO32 |
| WS512K32F-35H2C | 2M X 8 MULTI DEVICE SRAM MODULE, 35 ns, CHMA66 |
| WS512K32F-45G2TC | 2M X 8 MULTI DEVICE SRAM MODULE, 45 ns, CQMA68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25Q64CV | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q64CVDAAG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q64CVDAAP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q64CVDAIG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q64CVDAIP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
發布緊急采購，3分鐘左右您將得到回復。