- 您現在的位置：買賣IC網 > PDF目錄245698 > W25Q64BVZEIP (WINBOND ELECTRONICS CORP) 8M X 8 SPI BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | W25Q64BVZEIP |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 8M X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 8 X 6 MM, GREEN, WSON-8 |
| 文件頁數： | 20/61頁 |
| 文件大小： | 1726K |
| 代理商： | W25Q64BVZEIP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
W25Q64BV
Publication Release Date: July 08, 2010
- 27 -
Revision E
11.2.12 Fast Read Dual I/O (BBh)
The Fast Read Dual I/O (BBh) instruction allows for improved random access while maintaining two IO
pins, IO0 and IO1. It is similar to the Fast Read Dual Output (3Bh) instruction but with the capability to
input the Address bits (A23-0) two bits per clock. This reduced instruction overhead may allow for code
execution (XIP) directly from the Dual SPI in some applications. To ensure optimum performance the
High Performance Mode (HPM) instruction (A3h) must be executed once, prior to the Fast Read Dual I/O
Instruction.
Fast Read Dual I/O with “Continuous Read Mode”
The Fast Read Dual I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in figure 12a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Dual I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t care
(“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out clock.
If the “Continuous Read Mode” bits (M7-0) equals “Ax” hex, then the next Fast Read Dual I/O instruction
(after /CS is raised and then lowered) does not require the BBh instruction code, as shown in figure 12b.
This reduces the instruction sequence by eight clocks and allows the Read address to be immediately
entered after /CS is asserted low. If the “Continuous Read Mode” bits (M7-0) are any value other than
“Ax” hex, the next instruction (after /CS is raised and then lowered) requires the first byte instruction code,
thus returning to normal operation. A “Continuous Read Mode” Reset instruction can be used to reset
(M7-0) before issuing normal instructions (See 11.2.29 for detailed descriptions).
Figure 12a. Fast Read Dual Input/Output Instruction Sequence Diagram (M7-0 = 0xh or NOT Axh)
相關PDF資料 |
PDF描述 |
|---|---|
| W3DG634V7D2 | 4M X 64 SYNCHRONOUS DRAM MODULE, DMA168 |
| WPF512K8C70TFI5 | 512K X 8 FLASH 5V PROM, 70 ns, PDSO32 |
| WPF512K8C90TRM5 | 512K X 8 FLASH 5V PROM, 90 ns, PDSO32 |
| WS512K32F-35H2C | 2M X 8 MULTI DEVICE SRAM MODULE, 35 ns, CHMA66 |
| WS512K32F-45G2TC | 2M X 8 MULTI DEVICE SRAM MODULE, 45 ns, CQMA68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25Q64CV | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q64CVDAAG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q64CVDAAP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q64CVDAIG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q64CVDAIP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 64M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
發布緊急采購，3分鐘左右您將得到回復。