參數資料
型號： UPD70F3025AGC-33-8EU-A
廠商： Renesas Electronics America
文件頁數： 16/49頁
文件大?。?/td> 0K
描述： MCU 32BIT 256K FLASH 100LQFP
標準包裝： 50
系列： V853
核心處理器： V850ES
芯體尺寸： 32-位
速度： 33MHz
連通性： CSI，EBI/EMI，UART/USART
外圍設備： PWM
輸入/輸出數： 67
程序存儲器容量： 256KB（256K x 8）
程序存儲器類型： 閃存
RAM 容量： 8K x 8
電壓 - 電源 (Vcc/Vdd)： 4.5 V ~ 5.5 V
數據轉換器： A/D 8x10b，D/A 2x8b
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-LQFP
包裝： 托盤
2011 Microchip Technology Inc.
DS31037B-page 23
PIC24F16KL402 FAMILY
2.4
ICSP Pins
The PGC and PGD pins are used for In-Circuit Serial
Programming (ICSP) and debugging purposes. It
is recommended to keep the trace length between the
ICSP connector and the ICSP pins on the device as
short as possible. If the ICSP connector is expected to
experience an ESD event, a series resistor is recom-
mended, with the value in the range of a few tens of
ohms, not to exceed 100.
Pull-up resistors, series diodes and capacitors on the
PGC and PGD pins are not recommended as they will
interfere with the programmer/debugger communica-
tions to the device. If such discrete components are an
application requirement, they should be removed from
the circuit during programming and debugging. Alter-
natively, refer to the AC/DC characteristics and timing
requirements information in the respective device
Flash programming specification for information on
capacitive loading limits, and pin input voltage high
(VIH) and input low (VIL) requirements.
For device emulation, ensure that the “Communication
Channel Select” (i.e., PGCx/PGDx pins), programmed
into the device, matches the physical connections for
the ICSP to the Microchip debugger/emulator tool.
For
more
information
on
available
Microchip
development tools connection requirements, refer to
.
2.5
External Oscillator Pins
Many microcontrollers have options for at least two
oscillators: a high-frequency primary oscillator and a
low-frequency
secondary
oscillator
(refer
to
for details).
The oscillator circuit should be placed on the same
side of the board as the device. Place the oscillator
circuit close to the respective oscillator pins with no
more than 0.5 inch (12 mm) between the circuit
components and the pins. The load capacitors should
be placed next to the oscillator itself, on the same side
of the board.
Use a grounded copper pour around the oscillator cir-
cuit to isolate it from surrounding circuits. The
grounded copper pour should be routed directly to the
MCU ground. Do not run any signal traces or power
traces inside the ground pour. Also, if using a two-sided
board, avoid any traces on the other side of the board
where the crystal is placed.
Layout suggestions are shown in Figure 2-3. In-line
packages may be handled with a single-sided layout
that completely encompasses the oscillator pins. With
fine-pitch packages, it is not always possible to com-
pletely surround the pins and components. A suitable
solution is to tie the broken guard sections to a mirrored
ground layer. In all cases, the guard trace(s) must be
returned to ground.
FIGURE 2-3:
SUGGESTED PLACEMENT
OF THE OSCILLATOR
CIRCUIT
In planning the application’s routing and I/O assign-
ments, ensure that adjacent port pins and other
signals, in close proximity to the oscillator, are benign
(i.e., free of high frequencies, short rise and fall times,
and other similar noise).
GND
`
OSC1
OSC2
T1OSO
T1OS I
Copper Pour
Primary Oscillator
Crystal
Timer1 Oscillator
Crystal
DEVICE PINS
Primary
Oscillator
C1
C2
T1 Oscillator: C1
T1 Oscillator: C2
(tied to ground)
Single-Sided and In-Line Layouts:
Fine-Pitch (Dual-Sided) Layouts:
GND
OSCO
OSCI
Bottom Layer
Copper Pour
Oscillator
Crystal
Top Layer Copper Pour
C2
C1
DEVICE PINS
(tied to ground)
相關PDF資料
PDF描述
UPD70F3201YGC-YEU-A MCU 32BIT I2C 100TQFP
UPD70F3452GC-UBT-A MCU 32BIT 256KB FLASH 80LQFP
UPD70F3714GC-8BS-A MCU 32BIT V850ES/LX2 64-LQFP
UPD70F3757GJ-GAE-AX MCU 32BIT V850ES/HX3 144-LQFP
UPD720101GJ-UEN-A HOST CTLR USB 2.0 144-LQFP
相關代理商/技術參數
參數描述
UPD70F3030B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V850 Series Pamphlet | Pamphlet[02/2002]
UPD70F3030BY 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V850/SB1(TM).V850/SB2(TM) for Hardware | UM Including Electrical Characteristics[02/2003]
UPD70F3032A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:The RISC power shapes your imagination Pamphlet | Pamphlet[05/2002]
UPD70F3032AY 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V850 Family(TM) for Architecture | User＇s Manual[03/2001]
UPD70F3032B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V850 Series Pamphlet | Pamphlet[02/2002]
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*