- 您現在的位置：買賣IC網 > PDF目錄1971 > UPD70F3025AGC-33-8EU-A (Renesas Electronics America)MCU 32BIT 256K FLASH 100LQFP PDF資料下載
參數資料
| 型號： | UPD70F3025AGC-33-8EU-A |
| 廠商： | Renesas Electronics America |
| 文件頁數： | 15/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | MCU 32BIT 256K FLASH 100LQFP |
| 標準包裝： | 50 |
| 系列： | V853 |
| 核心處理器： | V850ES |
| 芯體尺寸： | 32-位 |
| 速度： | 33MHz |
| 連通性： | CSI，EBI/EMI，UART/USART |
| 外圍設備： | PWM |
| 輸入/輸出數： | 67 |
| 程序存儲器容量： | 256KB（256K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 8K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 數據轉換器： | A/D 8x10b，D/A 2x8b |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 100-LQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
PIC24F16KL402 FAMILY
DS31037B-page 22
2011 Microchip Technology Inc.
2.2
Power Supply Pins
2.2.1
DECOUPLING CAPACITORS
The use of decoupling capacitors on every pair of
power supply pins, such as VDD, VSS, AVDD and
AVSS, is required.
Consider the following criteria when using decoupling
capacitors:
Value and type of capacitor: A 0.1
F (100 nF),
10-20V capacitor is recommended. The capacitor
should be a low-ESR device, with a resonance
frequency in the range of 200 MHz and higher.
Ceramic capacitors are recommended.
Placement on the printed circuit board: The
decoupling capacitors should be placed as close
to the pins as possible. It is recommended to
place the capacitors on the same side of the
board as the device. If space is constricted, the
capacitor can be placed on another layer on the
PCB using a via; however, ensure that the trace
length from the pin to the capacitor is no greater
than 0.25 inch (6 mm).
Handling high-frequency noise: If the board is
experiencing high-frequency noise (upward of
tens of MHz), add a second ceramic type capaci-
tor in parallel to the above described decoupling
capacitor. The value of the second capacitor can
be in the range of 0.01
F to 0.001 F. Place this
second capacitor next to each primary decoupling
capacitor. In high-speed circuit designs, consider
implementing a decade pair of capacitances as
close to the power and ground pins as possible
(e.g., 0.1
F in parallel with 0.001 F).
Maximizing performance: On the board layout
from the power supply circuit, run the power and
return traces to the decoupling capacitors first,
and then to the device pins. This ensures that the
decoupling capacitors are first in the power chain.
Equally important is to keep the trace length
between the capacitor and the power pins to a
minimum, thereby reducing PCB trace
inductance.
2.2.2
TANK CAPACITORS
On boards with power traces running longer than
six inches in length, it is suggested to use a tank capac-
itor for integrated circuits, including microcontrollers, to
supply a local power source. The value of the tank
capacitor should be determined based on the trace
resistance that connects the power supply source to
the device, and the maximum current drawn by the
device in the application. In other words, select the tank
capacitor so that it meets the acceptable voltage sag at
the device. Typical values range from 4.7
F to 47 F.
2.3
Master Clear (MCLR) Pin
The MCLR pin provides two specific device
functions: Device Reset, and Device Programming
and Debugging. If programming and debugging are
not required in the end application, a direct
connection to VDD may be all that is required. The
addition of other components, to help increase the
application’s resistance to spurious Resets from
voltage
sags,
may
be
beneficial.
A
typical
configuration is shown in Figure 2-1. Other circuit
designs may be implemented, depending on the
application’s requirements.
During programming and debugging, the resistance
and capacitance that can be added to the pin must
be considered. Device programmers and debuggers
drive the MCLR pin. Consequently, specific voltage
levels (VIH and VIL) and fast signal transitions must
not be adversely affected. Therefore, specific values
of R1 and C1 will need to be adjusted based on the
application and PCB requirements. For example, it is
recommended that the capacitor, C1, be isolated
from the MCLR pin during programming and
debugging operations by using a jumper (Figure 2-2).
The
jumper
is
replaced
for
normal
run-time
operations.
Any components associated with the MCLR pin
should be placed within 0.25 inch (6 mm) of the pin.
FIGURE 2-2:
EXAMPLE OF MCLR PIN
CONNECTIONS
Note 1:
R1
10 k is recommended. A suggested
starting value is 10 k
. Ensure that the
MCLR pin VIH and VIL specifications are met.
2:
R2
470 will limit any current flowing into
MCLR from the external capacitor, C, in the
event of MCLR pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
VIH and VIL specifications are met.
C1
R2
R1
VDD
MCLR
PIC24FXXKXX
JP
相關PDF資料 |
PDF描述 |
|---|---|
| UPD70F3201YGC-YEU-A | MCU 32BIT I2C 100TQFP |
| UPD70F3452GC-UBT-A | MCU 32BIT 256KB FLASH 80LQFP |
| UPD70F3714GC-8BS-A | MCU 32BIT V850ES/LX2 64-LQFP |
| UPD70F3757GJ-GAE-AX | MCU 32BIT V850ES/HX3 144-LQFP |
| UPD720101GJ-UEN-A | HOST CTLR USB 2.0 144-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD70F3030B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V850 Series Pamphlet | Pamphlet[02/2002] |
| UPD70F3030BY | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V850/SB1(TM).V850/SB2(TM) for Hardware | UM Including Electrical Characteristics[02/2003] |
| UPD70F3032A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:The RISC power shapes your imagination Pamphlet | Pamphlet[05/2002] |
| UPD70F3032AY | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V850 Family(TM) for Architecture | User＇s Manual[03/2001] |
| UPD70F3032B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V850 Series Pamphlet | Pamphlet[02/2002] |
發布緊急采購，3分鐘左右您將得到回復。