- 您現在的位置：買賣IC網 > PDF目錄98080 > SII3114CT176 PCI BUS CONTROLLER, PQFP176 PDF資料下載
參數資料
| 型號： | SII3114CT176 |
| 元件分類： | 總線控制器 |
| 英文描述： | PCI BUS CONTROLLER, PQFP176 |
| 封裝： | TQFP-176 |
| 文件頁數： | 113/127頁 |
| 文件大?。?/td> | 564K |
| 代理商： | SII3114CT176 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁當前第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁
SiI3114 PCI to Serial ATA Controller
Data Sheet
Silicon Image, Inc.
SiI-DS-0103-D
78
2007 Silicon Image, Inc.
Write Operation
Wait until bit 27(DRQ) in the Channel x Task File Register 1 register is set.
Continue to write data via the Channel x Task File Register 0 register until the expected number of
sectors of data per interrupt are written.
Wait for a channel interrupt.
If controller interrupts are disabled, poll for the interrupt by reading the Channel x Task File Timing
+ Configuration + Status register. If bit 12 is set, a watchdog timeout has occurred. If bit 11 is set,
the ATA device is interrupting.
If the watchdog timeout bit is set,
Write 1 to bit 12 in the Channel x Task File Timing + Configuration + Status register to clear
watchdog timeout status.
The watchdog timeout represents a fatal error as far as the current ATA command is concerned.
A course of action that might be appropriate at this point might be to reset and reinitialize the ATA
channel and then retrying the command that failed.
If the ATA device interrupt bit is set,
Read the device status at bits [31:24] in the Channel x Task File Register 1 register to clear the
device interrupt and determine if there was an error.
Write 1 to bit 18 of the PCI Bus Master – Channel x Register to clear the ATA interrupt.
If no error, repeat the write operation steps until all data for the write command has been
transferred or an error has been detected.
PIO Mode Read Ahead Operation
Read ahead operation allows the controller to “pre-fetch” data and store it in the controller’s channel FIFO, where
it will later be retrieved by the host. This mode of operation has the potential to speed-up PIO data transfers by
not forcing the host to wait the programmed PIO cycle time for every access to the task file data register. The
amount of any speed increase will depend on the PIO mode in use, the characteristics of the host PCI bus, as
well as the speed of the host processor.
To use the controller’s PIO read ahead capability, make the following changes to the “Read Operation” portion of
the “PIO Mode Read/Write Operation” and “Watchdog Timer Operation” sections:
Just prior to retrieving the read data, set the read ahead byte count by programming bits [15:00] in the
Channel x Virtual DMA/PIO Read Ahead Byte Count register with the exact number of bytes to be read for
the interrupt.
Instead of reading the Channel x Task File Register 0 register to retrieve the data, read the Channel x Read
Ahead Data register.
MDMA/UDMA Read/Write Operation
Once the SiI3114 is initialized via the initialization sequence described in the “Recommended Initialization
Sequence for the SiI3114” section, and the SATA device has been initialized for MDMA/UDMA mode data transfer
per the guidelines in the “Serial ATA Device Initialization” section, DMA read/write operations may be performed
by following the programming sequence described below.
Issue a DMA read/write command to the device following the steps in the “Issue ATA Command” section on page
76.
Program Bus Master Registers
Clear bit 17 in the PCI Bus Master – Channel x register. This bit is set if an error occurred during the
previous DMA access.
Clear bit 18 in the PCI Bus Master – Channel x register. This bit is set if an interrupt occurred during the
previous DMA access.
相關PDF資料 |
PDF描述 |
|---|---|
| SII3114CTU | PCI BUS CONTROLLER, PQFP176 |
| SII3124ACBHU | PCI BUS CONTROLLER, PBGA364 |
| SII3512ECTU128 | PCI BUS CONTROLLER, PQFP128 |
| SII3531ACNU | PCI BUS CONTROLLER, QCC48 |
| SIO10N268-NU | MULTIFUNCTION PERIPHERAL, PQFP128 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII3114CTU | 制造商:Silicon Image Inc 功能描述:PCI to Serial ATA Controller 176-Pin TQFP 制造商:SILICON 功能描述: |
| SII3124A | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller |
| SII3124ACBHU | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller |
| SII3132 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI Express to 2-Port Serial ATA II Host Controller |
| SII3132CNU | 制造商:Silicon Image Inc 功能描述:PCI Express to Serial ATA Controller 88-Pin QFN |
發布緊急采購，3分鐘左右您將得到回復。