- 您現在的位置：買賣IC網 > PDF目錄16898 > SCFLXRAYADPTS12 (Freescale Semiconductor)ADAPTER BOARD FRDC PDF資料下載
參數資料
| 型號： | SCFLXRAYADPTS12 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 6/56頁 |
| 文件大?。?/td> | 0K |
| 描述： | ADAPTER BOARD FRDC |
| 標準包裝： | 1 |
| 系列： | * |
| 附件類型： | * |
| 適用于相關產品： | * |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
SCF5250 Data Sheet: Technical Data, Rev. 1.3
14
Freescale Semiconductor
3.4
Chip Selects
There are three chip select outputs on the SCF5250 device. CS0/CS4 and CS1/QSPI_CS3/GPIO28 and
CS2 which is associated with the IDE interface read and write strobes - IDE-DIOR and IDE-DIOW.
CS0 and CS4 are multiplexed. The SCF5250 has the option to boot from an internal Boot ROM.
The function of the CS0/CS4 pin is determined by the boot mode. When the device is booted from internal
ROM, the internal ROM is accessed with CS0 (required for boot) and the CS0/CS4 pin is driven by CS4.
When the device is booted from external ROM / Flash, the CS0/CS4 pin is driven by CS0 and the internal
ROM is disabled.
The active low chip selects can be used to access asynchronous memories. The interface is glueless.
3.5
ISA Bus
The SCF5250 supports an ISA bus. Using the ISA bus protocol, reads and writes for one ISA bus
peripheral is possible. IDE-DIOR/GPIO31 and IDE-DIOW/GPIO32 are the read and write strobe. The
peripheral can insert wait states by pulling IDE-IORDY/GPIO33.
CS2 is associated with the IDE-DIOR and IDE-DIOW.
3.6
Bus Buffer Signals
As the SCF5250 has a complicated slave bus, which allows SDRAM, asynchronous memories, and ISA
peripherals on the bus, it may become necessary to introduce a buffer on the bus in certain applications.
The SCF5250 has a glueless interface to steer these bus buffers with two bus buffer output signals
BUFENB1/GPIO29 and BUFENB2/GPIO30.
3.7
I2C Module Signals
The I2C module acts as a two-wire, bidirectional serial interface between the SCF5250 processor and
peripherals with an I2C interface (e.g., LED controller, A-to-D converter, D-to-A converter). When
devices connected to the I2C bus drive the bus, they will either drive logic-0 or high-impedance. This can
be accomplished with an open-drain output.
Table 4. I2C Module Signals
I2c Module Signal
Description
I2C Serial Clock
The SCL0/SDATA1_BS1/GPIO41 and SCL1/TXD1/GPIO10 bidirectional signals are the clock signal for
first and second I2C module operation. The I2C module controls this signal when the bus is in master
mode; all I2C devices drive this signal to synchronize I2C timing.
Signals are multiplexed
I2C Serial Data
The SDA0/SDATA3/GPIO42 and SDA1/RXD1/GPIO44 bidirectional signals are the data input/output for
the first and second serial I2C interface.
Signals are multiplexed
相關PDF資料 |
PDF描述 |
|---|---|
| LM4051CEM3-1.2+T | IC VREF SHUNT PREC 1.225V SOT23 |
| HBM06DSEF-S13 | CONN EDGECARD 12POS .156 EXTEND |
| 202A174-25/86-0 | BOOT MOLDED |
| MIC2566-0BTS TR | IC PCMCIA/CARDBUS SGL 14-TSSOP |
| 202A174-4/42-0 | BOOT MOLDED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SCFP1470 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| SCFR2502 | 制造商:FCI 制造商全稱:First Components International 功能描述:25.0 Amp SOZA CELL AUTO DIODE High surge current capability |
| SCFR2504 | 制造商:FCI 制造商全稱:First Components International 功能描述:25.0 Amp SOZA CELL AUTO DIODE High surge current capability |
| SCFR2506 | 制造商:FCI 制造商全稱:First Components International 功能描述:25.0 Amp SOZA CELL AUTO DIODE High surge current capability |
| SCFR3502 | 制造商:FCI 制造商全稱:First Components International 功能描述:35 Amps SOZA CELL AUTO DIODES High surge current capability |
發布緊急采購，3分鐘左右您將得到回復。