- 您現在的位置：買賣IC網 > PDF目錄98074 > SAF-C513A-HN (INFINEON TECHNOLOGIES AG) 8-BIT, EEPROM, 8 MHz, MICROCONTROLLER, PQCC44 PDF資料下載
參數資料
| 型號： | SAF-C513A-HN |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, EEPROM, 8 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 105/128頁 |
| 文件大?。?/td> | 1837K |
| 代理商： | SAF-C513A-HN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁當前第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
On-Chip Peripheral Units
Semiconductor Group
6-45
When the SSC is enabled and in master mode, pins P1.3/SRI, P1.4/STO, and P1.2/SCLK will be
switched to the SSC control function. P1.4/STO and P1.2/SCLK actively will drive the lines. P1.5/
SLS will remain a regular I/O pin.
The output latches of port pins dedicated to alternate functions must be programmed to logic 1
(= state after reset).
In slave mode all four control pins will be switched to the alternate function. However, STO will stay
in the tristate state until the transmitter is enabled by SLS input being low and the TEN control bit is
set to 1. This allows for more than one slave to be connected to one select line and the final
selection of the slave will be done by a software protocol.
6.4.4 Baudrate Generation (Master Mode only)
The baudrate clock is generated out of the processor clock (fosc divided by 2). This clock is fed into
a resetable divider with seven outputs for different baudrate clocks (fosc/8 to fosc/512). One of this
eight clocks is selected by the bits BRS2,1, 0 in SSCCON and provided to the shift control logic.
Whenever the shift register is loaded with a new value, the baudrate generation is restarted with the
trailing edge of the write signal to the shift register. In the case of CPHA = 0 the baudrate generator
will be restarted in a way, that the first SCLK clock transisition will not occur before one half transmit
clock cycle time after the register load. This ensures that there is sufficient setup time between MSB
valid on the data output and the first sample clock edge and that the MSB has the same length than
the other bits. (No special care is necessary in case of CPHA=1, because here the first clock edge
will be used for shifting).
6.4.5 Write Collision Detection
When an attempt is made to write data to the shift register while a transfer is in progress, the WCOL
bit in the status register will be set. The transfer in progress continues uninterrupted, the write will
not access the shift register and will not corrupt data.
However, the data written erroneously will be stored in a shadow register and can be read by
reading the STB register.
Depending on the operation mode there are different definitions for a transfer being considered to
be in progress:
Master Mode
CPHA=0:
from the trailing edge of the write into STB until the last sample clock edge
CPHA=1:
from the first SCLK clock edge until the last sample clock edge
Note, that this also means, that writing new data into STB immediately after the transfer
complete flag has been set (also initiated with the last sample clock edge) will not generate a
write collision. However, this may shorten the lenght of the last bit (especially at slow baudrates)
and prevent STO from switching to the forced "1" between transmissions.
Slave Mode
CPHA=0:
while SLS is active
CPHA=1:
from the first SCLK clock edge until the last sample clock edge
相關PDF資料 |
PDF描述 |
|---|---|
| SAF-C515A-LM | 8-BIT, 18 MHz, MICROCONTROLLER, PQFP80 |
| SAF-C515C-8EMCA | 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP80 |
| SAF-C517A-4R24M | 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
| SAF-C868-1RR | 8-BIT, MROM, 40 MHz, MICROCONTROLLER, PDSO38 |
| SAF-C868-1SR | 8-BIT, 40 MHz, MICROCONTROLLER, PDSO38 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAF-C513AO | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-bit CMOS Microcontroller |
| SAF-C515 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller |
| SAF-C515-1R24M | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller |
| SAF-C515-1RM | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller |
| SAF-C515A-4R | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。