- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C60N04D 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC48 PDF資料下載
參數資料
| 型號： | S1C60N04D |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC48 |
| 封裝： | DIE-48 |
| 文件頁數： | 32/50頁 |
| 文件大?。?/td> | 372K |
| 代理商： | S1C60N04D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
32
EPSON
S1C60N04 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Interrupt and HALT/SLEEP)
4.8.5 Programming notes
(1) Restart from the HALT mode is performed by an interrupt. The return address after completion of the
interrupt processing will be the address following the HALT instruction.
(2) Restart from the SLEEP mode is performed by an input interrupt from the input port (K00–K03). The
return address after completion of the interrupt processing will be the address following the SLP
instruction. At least one input port interrupt must be enabled before shifting to the SLEEP mode.
(3) When an interrupt occurs, the interrupt flag will be reset by the hardware and it will become DI
status. After completion of the interrupt processing, set to the EI status through the software as
needed.
Moreover, the nesting level may be set to be programmable by setting to the EI state at the beginning
of the interrupt processing routine.
(4) The interrupt factor flags must always be reset before setting the EI status. When the interrupt mask
register has been set to 1, the same interrupt will occur again if the EI status is set unless of resetting
the interrupt factor flag.
(5) The interrupt factor flag will be reset by reading through the software. Because of this, when multiple
interrupt factor flags are to be assigned to the same address, perform the flag check after the contents
of the address has been stored in the RAM. Direct checking with the FAN instruction will cause all the
interrupt factor flag to be reset.
(6) Reading of interrupt factor flag is available at EI, but be careful in the following cases.
If the interrupt mask register value corresponding to the interrupt factor flag to be read is set to 1, an
interrupt request will be generated by the interrupt factor flag set timing, or an interrupt request will
not be generated. Be very careful when interrupt factor flags are in the same address.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C60N08D | 4-BIT, MROM, 0.032768 MHz, MICROCONTROLLER, UUC96 |
| S1C60N08F0A0100 | MICROCONTROLLER, PQFP100 |
| S1C621C0D | 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC74 |
| S1C62480D | 4-BIT, MROM, 2.3 MHz, MICROCONTROLLER, UUC135 |
| S1C62440F | 4-BIT, MROM, 2.3 MHz, MICROCONTROLLER, PQFP128 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C60N05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N16 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60R08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63004 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。