參數資料
型號： PI7C21P100
廠商： Pericom Semiconductor Corp.
英文描述： 2-PORT PCI-X BRIDGE
中文描述： 2端口PCI - X橋接
文件頁數： 15/77頁
文件大小： 603K
代理商： PI7C21P100
PI7C21P100
2-PORT PCI-X BRIDGE
ADVANCE INFORMATION
Page 15 of 77
June 10, 2005 Revision 1.06
Name
S_PAR64
Pin #
AA10
Type
TS
Description
Secondary Upper 32-bit Parity:
S_PAR64 carries the
even parity of S_AD[63:32] and S_CBE[7:4] for both
address and data phases. S_PAR64 is driven by the
initiator and is valid 1 cycle after the first address phase
when a dual address command is used and S_REQ64# is
asserted. S_PAR64 is valid 1 clock cycle after the
second address phase of a dual address transaction when
S_REQ64# is asserted. S_PAR64 is valid 1 cycle after
valid data is driven when both S_REQ64# and
S_ACK64# are asserted for that data phase. S_PAR64 is
driven by the device driving read or write data 1 cycle
after the S_AD lines are driven. S_PAR64 is tri-stated 1
cycle after the S_AD lines are tri-stated. Devices receive
data sample S_PAR64 as an input to check for possible
parity errors during 64-bit transactions. When not driven,
S_PAR64 is pulled up to a valid logic level through
external resistors.
Secondary 64-bit Transfer Request:
S_REQ64# is
asserted by the initiator to indicate that the initiator is
requesting a 64-bit data transfer. S_REQ64# has the
same timing as S_FRAME#. When S_REQ64# is
asserted LOW during reset, a 64-bit data path is
supported. When S_REQ64# is HIGH during reset,
PI7C21P100 drives S_AD[63:32], S_CBE[7:4], and
S_PAR64 to valid logic levels. When deasserting,
S_REQ64# is driven to a deasserted state for 1 cycle and
then sustained by an external pull-up resistor.
Secondary 64-bit Transfer Acknowledge:
S_ACK64#
is asserted by the target only when S_REQ64# is
asserted by the initiator to indicate the target’s ability to
transfer data using 64 bits. S_ACK64# has the same
timing as S_DEVSEL#. When deasserting, S_ACK64#
is driven to a deasserted state for 1 cycle and then is
sustained by an external pull-up resistor.
S_REQ64#
AB13
STS
S_ACK64#
AA8
STS
3.2.5
CLOCK SIGNALS
Name
P_CLK
Pin #
E21
Type
I
Description
Primary Clock Input:
Provides timing for all
transactions on the primary interface. For conventional
PCI mode, the input clock frequency may be between 0
– 66MHz. In PCI-X mode, the input clock frequency
may be between 66 – 133MHz. See Section 6 for
limitations.
Secondary Clock Input:
Provides timing for all
transactions on the secondary interface. For conventional
PCI mode, the input clock frequency may be between 0
– 66MHz. In PCI-X mode, the input clock frequency
may be between 66 – 133MHz. See Section 6 for
limitations. If the primary bus is running at 133MHz,
the minimum frequency that may be supplied to S_CLK
is 33MHz.
S_CLK
AB23
I
相關PDF資料
PDF描述
PI7C21P100NH 2-PORT PCI-X BRIDGE
PI7C7100BNA PCI Bus Interface/Controller
PI7C7100 3-Port PCI Bridge
PI7C7100CNA 3-Port PCI Bridge
PI7C7300 3-PORT PCI-to-PCI BRIDGE
相關代理商/技術參數
參數描述
PI7C21P100B 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2-PORT PCI-X TO PCI-X BRIDGE
PI7C21P100BEVB 功能描述:界面開發工具 3 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
PI7C21P100BNH 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:2-PORT PCI-X TO PCI-X BRIDGE
PI7C21P100BNHE 功能描述:外圍驅動器與原件 - PCI PCI-X to PCI-XBridge 2 Port RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
PI7C21P100EVB 功能描述:界面開發工具 3 Port PCI Bridge Eval Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*