- 您現在的位置：買賣IC網 > PDF目錄367820 > PCF8811 (NXP Semiconductors N.V.) 80 x 128 pixels matrix LCD driver PDF資料下載
參數資料
| 型號： | PCF8811 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 80 x 128 pixels matrix LCD driver |
| 中文描述： | 80 × 128像素矩陣LCD驅動器 |
| 文件頁數： | 59/73頁 |
| 文件大?。?/td> | 434K |
| 代理商： | PCF8811 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
2004 May 17
59
Philips Semiconductors
Product specification
80
×
128 pixels matrix LCD driver
PCF8811
handbook, full pagewidth
MSB
0
LSB
shifting
direction
0
MGW765
MMTC[2:0]
SEAL
BIT = 0
1
MSB
1
LSB
0
MMVOPCAL[4:0]
OTP SHIFT REGISTER
0
1
1
Fig.49 Shift register contents after example sequence of Table 25.
22.7
Programming flow
Programming is achieved whilst in CALMM mode and with
the application of the programming voltages. As
mentioned previously, the data for programming the OTP
cell is contained in the corresponding shift register cell.
The shift register cell must be loaded with a logic 1 in order
to program the corresponding OTP cell. If the shift register
cell contains a logic 0, then no action will take place when
the programming voltages are applied.
Once programmed, an OTP cell cannot be
de-programmed. An already programmed cell, i.e. an OTP
cell containing a logic 1, must not be re-programmed.
During programming a substantial current flows in the
V
LCDIN
pin. For this reason it is recommended to program
only one OTP cell at a time. This is achieved by filling all
but one shift register cells with logic 0.
It should be noted that the programming specification
refers to the voltages at the chip pins, contact resistance
must therefore be considered by the user.
An example sequence of commands and data for OTP
programming is given in Table 26.
The order for programming cells is not significant.
However, it is recommended that the seal bit is
programmed last. Once this bit has been programmed it
will not be possible to re-enter the CALMM mode.
It is assumed that the PCF8811 has just been reset.
相關PDF資料 |
PDF描述 |
|---|---|
| PCF8812 | CRYSTAL, 8.0 MHZ |
| PCF8812U | CRYSTAL, 8,0 MHZ |
| PCF8813 | (67 + 1) x 102 pixels matrix LCD driver |
| PCF88132 | (67 + 1) x 102 pixels matrix LCD driver |
| PCF88132DA | (67 + 1) x 102 pixels matrix LCD driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF8811MU/2DA/1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver |
| PCF8811MU/2DA/1,02 | 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle 制造商:NXP Semiconductors 功能描述:PCF8811MU/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle Waffle 制造商:NXP Semiconductors 功能描述:IC LCD CTLR/DVR CMOS LP UNCASED 制造商:NXP Semiconductors 功能描述:80 x 128 Pixels Matrix LCD Driver |
| PCF8811U/2DA/1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver |
| PCF8811U/2DA/1，026 | 制造商:NXP Semiconductors 功能描述:PCF8811U/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:IC MATRIX LCD DRIVER UNCASED |
| PCF8812 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:65 x 102 pixels matrix LCD driver |
發布緊急采購，3分鐘左右您將得到回復。