參數資料
型號： PCF8811
廠商： NXP Semiconductors N.V.
英文描述： 80 x 128 pixels matrix LCD driver
中文描述： 80 × 128像素矩陣LCD驅動器
文件頁數： 18/73頁
文件大?。?/td> 434K
代理商： PCF8811
2004 May 17
18
Philips Semiconductors
Product specification
80
×
128 pixels matrix LCD driver
PCF8811
handbook, full pagewidth
RES
SCLK
SDATA
DB7
DB6
DB5
DB4
DB2
DB3
DB1 DB0
SDO
instruction
DB2
DB7
DB6
DB5
DB4
DB3
DB1 DB0
MGW748
read out data
Fig.16 Read mode SPI 3-line and 4-line.
11.2
Serial interface (3-line)
The serial interface is also a 3-line bidirectional interface
for communication between the microcontroller and the
LCD driver chip. The 3 lines are: SCE (chip enable), SCLK
(serial clock) and SDATA (serial data). The PCF8811 is
connected to the SDA of the microcontroller by two pins:
SDATA (data input) and SDO (data output) which are
connected together.
11.2.1
W
RITE MODE
The write mode of the interface means that the
microcontroller writes commands and data to the
PCF8811. Each data packet contains a control bit (D/C)
and a transmission byte. If D/C is LOW, the following byte
is interpreted as a command byte. The command set is
given in Table 5. If D/C is HIGH, the following byte is
stored in the display data RAM. After every data byte the
address counter is incremented automatically. Figure 17
shows the general format of the write mode and the
definition of the transmission byte.
Any instruction can be sent in any order to the PCF8811;
the MSB is transmitted first. The serial interface is
initialized when SCE is HIGH. In this state, SCLK clock
pulses have no effect and no power is consumed by the
serial interface. A falling edge on SCE enables the serial
interface and indicates the start of data transmission.
Figures 18, 19 and 20 show the protocol of the write
mode:
When SCE is HIGH, SCLK clocks are ignored; during
the HIGH time of SCE the serial interface is initialized
SCLK must be LOW on the falling SCE edge (see
Fig.37)
SDATA is sampled on the rising edge of SCLK
D/C indicates, whether the byte is a command (D/C = 0)
or RAM data (D/C = 1); it is sampled on the first rising
SCLK edge
If SCE stays LOW after the last bit of a command/data
byte, the serial interface receives the D/C bit of the next
byte on the next rising edge of SCLK (see Fig.19)
A reset pulse RES interrupts the transmission. The data
being written into the RAM may be corrupted. The
registers are cleared. If SCE is LOW after the rising
edge of RES, the serial interface is ready to receive the
D/C bit of a command/data byte (see Fig.20).
相關PDF資料
PDF描述
PCF8812 CRYSTAL, 8.0 MHZ
PCF8812U CRYSTAL, 8,0 MHZ
PCF8813 (67 + 1) x 102 pixels matrix LCD driver
PCF88132 (67 + 1) x 102 pixels matrix LCD driver
PCF88132DA (67 + 1) x 102 pixels matrix LCD driver
相關代理商/技術參數
參數描述
PCF8811MU/2DA/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver
PCF8811MU/2DA/1,02 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle 制造商:NXP Semiconductors 功能描述:PCF8811MU/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle Waffle 制造商:NXP Semiconductors 功能描述:IC LCD CTLR/DVR CMOS LP UNCASED 制造商:NXP Semiconductors 功能描述:80 x 128 Pixels Matrix LCD Driver
PCF8811U/2DA/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver
PCF8811U/2DA/1，026 制造商:NXP Semiconductors 功能描述:PCF8811U/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:IC MATRIX LCD DRIVER UNCASED
PCF8812 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:65 x 102 pixels matrix LCD driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*