參數資料
型號： PCF8811
廠商： NXP Semiconductors N.V.
英文描述： 80 x 128 pixels matrix LCD driver
中文描述： 80 × 128像素矩陣LCD驅動器
文件頁數： 24/73頁
文件大?。?/td> 434K
代理商： PCF8811
2004 May 17
24
Philips Semiconductors
Product specification
80
×
128 pixels matrix LCD driver
PCF8811
Table 4
Co and D/C definition
BIT
LOGIC
LEVEL
R/W
ACTION
Co
0
N/A
last control byte to be sent; only a stream of data bytes are allowed to follow; this stream
may only be terminated by a STOP or RE-START condition
another control byte will follow the data byte unless a STOP or RE-START condition is
received
data byte will be decoded and used to set-up the device
data byte will return the status byte
data byte will be stored in the display RAM
RAM read back is not supported
1
D/C
0
0
1
0
1
1
A read sequence is given in Fig.29 and again this
sequence follows after the Hs-mode is selected. The
PCF8811 will immediately start to output the requested
data until a not-acknowledge is transmitted by the master.
Before the read access, the user has to set the D/C bit to
the appropriate value by a preceding write access. The
write access should be terminated by a RE-START
condition so that the Hs-mode is not disabled.
After the last control byte, depending on the D/C bit
setting, either a series of display data bytes or command
data bytes may follow. If the D/C bit was set to logic 1,
these display bytes are stored in the display RAM at the
address specified by the data pointer.
The data pointer is automatically updated and the data is
directed to the intended PCF8811 device. If the D/C bit of
the last control byte was set to logic 0, these command
bytes will be decoded and the setting of the device will be
changed according to the received commands. The
acknowledgement after each byte is made only by the
addressed PCF8811. At the end of the transmission the
I
2
C-bus master issues a STOP condition (P) and switches
back to the F/S-mode, however, to reduce the overhead of
the master code, it is possible that a master can link
a number of Hs-mode transfers, separated by repeated
START conditions (Sr).
handbook, full pagewidth
F/S-mode
Hs-mode (current-source for SCLH enabled)
F/S-mode
MSC616
A
A
A/A
DATA
(n bytes
+
ack.)
S
R/W
MASTER CODE
Sr
SLAVE ADD.
Hs-mode continues
Sr SLAVE ADD.
P
Fig.26 Data transfer format in Hs-mode.
相關PDF資料
PDF描述
PCF8812 CRYSTAL, 8.0 MHZ
PCF8812U CRYSTAL, 8,0 MHZ
PCF8813 (67 + 1) x 102 pixels matrix LCD driver
PCF88132 (67 + 1) x 102 pixels matrix LCD driver
PCF88132DA (67 + 1) x 102 pixels matrix LCD driver
相關代理商/技術參數
參數描述
PCF8811MU/2DA/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver
PCF8811MU/2DA/1,02 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle 制造商:NXP Semiconductors 功能描述:PCF8811MU/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle Waffle 制造商:NXP Semiconductors 功能描述:IC LCD CTLR/DVR CMOS LP UNCASED 制造商:NXP Semiconductors 功能描述:80 x 128 Pixels Matrix LCD Driver
PCF8811U/2DA/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver
PCF8811U/2DA/1，026 制造商:NXP Semiconductors 功能描述:PCF8811U/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:IC MATRIX LCD DRIVER UNCASED
PCF8812 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:65 x 102 pixels matrix LCD driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*