- 您現在的位置：買賣IC網 > PDF目錄367820 > PCF8811 (NXP Semiconductors N.V.) 80 x 128 pixels matrix LCD driver PDF資料下載
參數資料
| 型號： | PCF8811 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 80 x 128 pixels matrix LCD driver |
| 中文描述： | 80 × 128像素矩陣LCD驅動器 |
| 文件頁數： | 29/73頁 |
| 文件大?。?/td> | 434K |
| 代理商： | PCF8811 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
2004 May 17
29
Philips Semiconductors
Product specification
80
×
128 pixels matrix LCD driver
PCF8811
Notes
1.
2.
X = don’t care.
Philips strongly recommends that the extended
command set be used.
D7 = MSB.
Commands only available with the extended
command set, EXT = 1. If EXT = 0 these commands
have no effect.
When icon mode is enabled the set initial display line
is 0
≤
L
≤
78.
When icon mode is enabled the set initial row is
0
≤
C
≤
78.
Commands only used for the basic command set,
EXT = 0. If EXT = 1 these commands have no effect.
Care should be taken when setting V
OP
in the basic
command set, it must be followed by another
command.
3.
4.
5.
6.
7.
8.
The programming of V
OP
in the basic command set
must be done in the following order:
a) V
PR
[5:0]
b) V
OFF
[2:0]
c) Must be followed by another command.
One fixed TC is set automatically if the basic
command set is used.
10. Bias system settings which can be received when the
chip is used as replacement of Alth and Pleskho
driving method (NOP).
11. Only for mux rates 1 : 64 and 1 : 80 the number of
simultaneous rows can be manually set to p = 4.
9.
13.1
Explanation of the symbols
13.1.1
C
OMMON
I
NSTRUCTIONS OF THE BASIC AND EXTENDED COMMAND SET
Table 6
Explanation of the symbols
BIT
LOGIC 0
LOGIC 1
RESET STATE
DON
E
DAL
MX
MY
OC
display off
normal display
normal display
no X mirroring
no Y mirroring
stop frame frequency
calibration
internal oscillator off
sets X address (column) for writing in the RAM
sets Yaddress (bank) for writing in the RAM
set wrap around X address (column)
set wrap around Yaddress (bank)
sets line address of the display RAM to be displayed on the initial
ROW 0
sets the initial ROW 0 of the display; this command cannot
access the icon driver row ROW 80; if icon row is enabled
partial display mode 1 : 16 to 1 : 80; note 1
display on
inverse video mode
all pixels on
X mirroring
Y mirroring
start frame frequency calibration 0
0
0
0
0
0
OS
X[6:0]
Y[3:0]
Xmax[6:0]
Ymax[3:0]
L[6:0]
start internal oscillator
0
0000000
0000
1111111
1001
0000000
C[6:0]
0000000
P[6:0]
1010000 (1 : 80)/1000000
(1 : 64)
00
00
PC[1:0]
S[1:0]
switch HV generator on/off
charge pump multiplication factor
相關PDF資料 |
PDF描述 |
|---|---|
| PCF8812 | CRYSTAL, 8.0 MHZ |
| PCF8812U | CRYSTAL, 8,0 MHZ |
| PCF8813 | (67 + 1) x 102 pixels matrix LCD driver |
| PCF88132 | (67 + 1) x 102 pixels matrix LCD driver |
| PCF88132DA | (67 + 1) x 102 pixels matrix LCD driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF8811MU/2DA/1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver |
| PCF8811MU/2DA/1,02 | 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle 制造商:NXP Semiconductors 功能描述:PCF8811MU/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle Waffle 制造商:NXP Semiconductors 功能描述:IC LCD CTLR/DVR CMOS LP UNCASED 制造商:NXP Semiconductors 功能描述:80 x 128 Pixels Matrix LCD Driver |
| PCF8811U/2DA/1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver |
| PCF8811U/2DA/1，026 | 制造商:NXP Semiconductors 功能描述:PCF8811U/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:IC MATRIX LCD DRIVER UNCASED |
| PCF8812 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:65 x 102 pixels matrix LCD driver |
發布緊急采購，3分鐘左右您將得到回復。