參數資料
型號： PCF8811
廠商： NXP Semiconductors N.V.
英文描述： 80 x 128 pixels matrix LCD driver
中文描述： 80 × 128像素矩陣LCD驅動器
文件頁數： 23/73頁
文件大?。?/td> 434K
代理商： PCF8811
2004 May 17
23
Philips Semiconductors
Product specification
80
×
128 pixels matrix LCD driver
PCF8811
handbook, full pagewidth
MBC602
S
START
condition
9
8
2
1
clock pulse for
acknowledgement
not acknowledge
acknowledge
DATA OUTPUT
BY TRANSMITTER
DATA OUTPUT
BY RECEIVER
SCL FROM
MASTER
Fig.25 Acknowledge on the I
2
C-bus.
12.2
I
2
C-bus Hs-mode protocol
The PCF8811 is a slave receiver/transmitter. If data is to
bereadfromthedevice,theSDAHpinmustbeconnected,
otherwise SDAH may be unused.
Hs-mode can only commence after the following
conditions:
START condition (S)
8-bit master code (00001XXX)
Not-acknowledge bit (A).
The master code has two functions: it allows arbitration
and synchronization between competing masters at
F/S-mode speeds, resulting in one winner. The master
code also indicates the beginning of an Hs-mode transfer.
These conditions are illustrated in Figs 26 and 27.
As no device is allowed to acknowledge the master code,
the master code is followed by a not-acknowledge (A).
After this A bit, and the SCLH line has been pulled up to
a HIGH level, the active master switches to Hs-mode and
enables at t
H
the current-source pull-up circuit for the
SCLH signal (see Fig.27).
The active master will then send a repeated START
condition (Sr) followed by a 7-bit slave address with a R/W
bit, and receives an acknowledge bit (A) from the selected
slave.
After each acknowledge bit (A) or not-acknowledge bit (A)
theactivemasterdisablesitscurrentsourcepull-upcircuit.
The active master re-enables its current source again
when all devices have been released and the SCLH signal
reaches a HIGH level. The rising of the SCLH signal is
done by a pull-up resistor and therefore is slower, the last
part of the SCLH rise time is speeded up because the
current source is enabled. Data transfer only switches
back to F/S mode after a STOP condition (P).
A write sequence after the Hs-mode is selected is
illustrated in Fig.28. The sequence is initiated with
a START condition (S) from the I
2
C-bus master which is
followed by the slave address. All slaves with the
corresponding address acknowledge in parallel, the
remainder will ignore the I
2
C-bus transfer.
After the acknowledgement cycle of a write (W), one or
more command words will follow which define the status of
the addressed slaves. A command word consists of
a control byte, which defines Co and D/C, plus a data byte
(see Fig.28 and Table 4).
The last control byte is tagged with a cleared MSB, the
continuation bit Co. The control and data bytes are also
acknowledged by all addressed slaves on the bus.
相關PDF資料
PDF描述
PCF8812 CRYSTAL, 8.0 MHZ
PCF8812U CRYSTAL, 8,0 MHZ
PCF8813 (67 + 1) x 102 pixels matrix LCD driver
PCF88132 (67 + 1) x 102 pixels matrix LCD driver
PCF88132DA (67 + 1) x 102 pixels matrix LCD driver
相關代理商/技術參數
參數描述
PCF8811MU/2DA/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver
PCF8811MU/2DA/1,02 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle 制造商:NXP Semiconductors 功能描述:PCF8811MU/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle Waffle 制造商:NXP Semiconductors 功能描述:IC LCD CTLR/DVR CMOS LP UNCASED 制造商:NXP Semiconductors 功能描述:80 x 128 Pixels Matrix LCD Driver
PCF8811U/2DA/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver
PCF8811U/2DA/1，026 制造商:NXP Semiconductors 功能描述:PCF8811U/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:IC MATRIX LCD DRIVER UNCASED
PCF8812 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:65 x 102 pixels matrix LCD driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*