參數資料
型號: PCF8811
廠商: NXP Semiconductors N.V.
英文描述: 80 x 128 pixels matrix LCD driver
中文描述: 80 × 128像素矩陣LCD驅動器
文件頁數: 26/73頁
文件大?。?/td> 434K
代理商: PCF8811
2004 May 17
26
Philips Semiconductors
Product specification
80
×
128 pixels matrix LCD driver
PCF8811
handbook, full pagewidth
MGW750
Sr 0 1 1 1 1
S
A
0
S
A
1
1 A
acknowledgement
from PCF8811
NOT acknowledgement
from Master
status information
A
slave address
STOP condition
P
R/W
Fig.29 Master receives from slave transmitter (status register is read); read mode.
12.3
Command decoder
The command decoder identifies command words that are
received on the I
2
C-bus:
Pairs of bytes: information in 2nd byte, first byte
determines whether information is display or instruction
data
Stream of information bytes after Co = 0: display or
instruction data depending on last D/C.
The most significant bit of a control byte is the continuation
bit Co. If this bit is at logic 1, it indicates that only one data
byte, either command or RAM data, will follow. If this bit is
at logic 0, it indicates that a series of data bytes, either
command or RAM data, may follow. The DB6 bit of a
control byte is the RAM data/command bit D/C. When this
bit is at logic 1, it indicates that a RAM data byte will be
transferred next. If the bit is at logic 0, it indicates that a
command byte will be transferred next.
13 INSTRUCTIONS
The PCF8811 interfaces via an 8-bit parallel interface, two
different 3-line serial interfaces, a 4-wire serial interface or
an I
2
C-bus interface. Processing of the instructions does
not require the display clock.
Data accesses to the PCF8811 can be broken down into
two areas; those that define the operating mode of the
device, and those that fill the display RAM.
In the case of the parallel and 4-wire SPI interfaces, the
distinction is the D/C pin. When the D/C pin is at logic 0,
the chip will respond to instructions as defined in Table 5.
When the D/C bit is at logic 1, the chip will send data to the
RAM.
When the 3-wire SPI, the 3-wire serial interface or the
I
2
C-bus interface is used, the distinction between
instructions which define the operating mode of the device
and those that fill the display RAM, is made respectively by
the display data length instruction (3-line SPI) or by the
D/C bit in the data stream (3-line serial interface and
I
2
C-bus interface).
There are 4 types of instructions. Those which:
1.
Define the PCF8811 functions, such as display
configuration etc.
2.
Set internal RAM addresses
3.
Perform data transfer with internal RAM
4.
Others.
In normal use, category 3 instructions are used most
frequently.
A basic and an extended instruction set is available: if the
EXT pin is set LOW the basic command set is used. If the
EXT pin is set HIGH the extended command set is used.
Both command sets are detailed in Table 5.
相關PDF資料
PDF描述
PCF8812 CRYSTAL, 8.0 MHZ
PCF8812U CRYSTAL, 8,0 MHZ
PCF8813 (67 + 1) x 102 pixels matrix LCD driver
PCF88132 (67 + 1) x 102 pixels matrix LCD driver
PCF88132DA (67 + 1) x 102 pixels matrix LCD driver
相關代理商/技術參數
參數描述
PCF8811MU/2DA/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver
PCF8811MU/2DA/1,02 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle 制造商:NXP Semiconductors 功能描述:PCF8811MU/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle Waffle 制造商:NXP Semiconductors 功能描述:IC LCD CTLR/DVR CMOS LP UNCASED 制造商:NXP Semiconductors 功能描述:80 x 128 Pixels Matrix LCD Driver
PCF8811U/2DA/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver
PCF8811U/2DA/1,026 制造商:NXP Semiconductors 功能描述:PCF8811U/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:IC MATRIX LCD DRIVER UNCASED
PCF8812 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:65 x 102 pixels matrix LCD driver