參數資料
型號： PCF8811
廠商： NXP Semiconductors N.V.
英文描述： 80 x 128 pixels matrix LCD driver
中文描述： 80 × 128像素矩陣LCD驅動器
文件頁數： 58/73頁
文件大?。?/td> 434K
代理商： PCF8811
2004 May 17
58
Philips Semiconductors
Product specification
80
×
128 pixels matrix LCD driver
PCF8811
22.5.2
R
EFRESH
The action of the ‘Refresh’ instruction is to force the OTP
shift register to re-load from the non-volatile OTP cells.
This instruction takes up to 5 ms to complete. During this
time all other instructions may be sent.
In the PCF8811 the ‘Refresh’ instruction is associated with
the ‘Power control’ instruction so that the shift register is
automatically refreshed every time the high voltage
generator is enabled or disabled. It should be noted
however, that if this instruction is sent while in the
power-save mode, the PC[1:0] bits will be updated but the
refreshing will be ignored.
22.6
Example of filling the shift register
An example of the sequence of commands and data is
showninTable 25.Inthisexampletheshiftregisterisfilled
with the following data: MMVOPCAL =
4 (11100 BIN),
MMTC = 2 (010 BIN) and the seal bit is 0.
It is assumed that the PCF8811 has just been reset. After
transmitting the last bit the PCF8811 can exit or remain in
the CALMM mode (see step 1). It should be noted that
while in CALMM mode the interface does not recognize
commands in the normal sense.
After this sequence has been applied it is possible to
observe the impact of the data shifted in. The described
sequence is, however, not useful for OTP programming
because the number of bits with the value logic 1 is greater
than that allowed for programming; see Section 22.7.
Figure 49 shows the shift register after this action.
Table 25
Example sequence for filling the shift register; note 1
Notes
1.
2.
X = don’t care.
The data for the bits is not in the correct shift register position until all bits have been sent.
STEP
EXT
D/C
R/W
D7
D6
D5
D4
D3
D2
D1
D0
ACTION
1
2
3
4
X
0
0
1
1
1
0
0
0
0
1
exit Power-down
wait 5 ms for refresh to take effect
enter CALMM mode
shift in data. MMVOPCAL[4] is first
bit; note 2
MMVOPCAL[3]
MMVOPCAL[2]
MMVOPCAL[1]
MMVOPCAL[0]
MMTC[2]
MMTC[1]
MMTC[0]
seal bit; exit CALMM mode
X
X
0
0
0
0
1
1
0
X
0
X
0
X
0
X
0
X
1
X
0
1
5
6
7
8
9
10
11
12
An alternative ending could be to stay in CALMM mode
13
X
0
0
X
X
X
X
X
X
X
X
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1
1
0
0
0
1
0
0
1
X
X
X
X
X
X
0
seal bit; remain in CALMM mode
相關PDF資料
PDF描述
PCF8812 CRYSTAL, 8.0 MHZ
PCF8812U CRYSTAL, 8,0 MHZ
PCF8813 (67 + 1) x 102 pixels matrix LCD driver
PCF88132 (67 + 1) x 102 pixels matrix LCD driver
PCF88132DA (67 + 1) x 102 pixels matrix LCD driver
相關代理商/技術參數
參數描述
PCF8811MU/2DA/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver
PCF8811MU/2DA/1,02 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle 制造商:NXP Semiconductors 功能描述:PCF8811MU/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:LCD DRVR 1.8V/2.5V Die Waffle Waffle 制造商:NXP Semiconductors 功能描述:IC LCD CTLR/DVR CMOS LP UNCASED 制造商:NXP Semiconductors 功能描述:80 x 128 Pixels Matrix LCD Driver
PCF8811U/2DA/1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80 x 128 pixels matrix LCD driver
PCF8811U/2DA/1，026 制造商:NXP Semiconductors 功能描述:PCF8811U/UNCASED/WAFLM//2DA/1 - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:NXP Semiconductors 功能描述:IC MATRIX LCD DRIVER UNCASED
PCF8812 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:65 x 102 pixels matrix LCD driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*