- 您現在的位置：買賣IC網 > PDF目錄382377 > PCA5010 (NXP Semiconductors N.V.) Pager baseband controller PDF資料下載
參數資料
| 型號： | PCA5010 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Pager baseband controller |
| 中文描述： | 傳呼機基帶控制器 |
| 文件頁數： | 61/112頁 |
| 文件大?。?/td> | 627K |
| 代理商： | PCA5010 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
1998 Nov 02
61
Philips Semiconductors
Product specification
Pager baseband controller
PCA5010
2.
If logic 1s are written to PD and IDL at the same time,
PD takes precedence. The reset value of PCON is
(00000000).
6.21
Reset
To initialize the PCA5010 a reset is performed by either of
2 methods:
Applying an external reset signal to the RESETIN pin
Via the on-chip watchdog timer.
The reset state of the output pins is given in separate
tables (Tables 2 to 6). The reset state of SFRs is given in
a separate overview (see Table 1).
While a reset is applied to the device the output RESOUT
is driven LOW.
The internal RAM is not affected by reset. When V
DD
is
turned on, the RAM contents are indeterminate.
6.21.1
E
XTERNAL RESET USING THE
RESETIN
PIN
The external reset input for the PCA5010 is the RESETIN
pin. A Schmitt trigger is used at the input for noise
rejection. Immediately after the RESETIN goes HIGH, an
internal reset is executed. As a consequence the SFRs
and port pins adopt their reset state, ALE and PSEN are
held HIGH. As long as RESETIN pin stays HIGH, the reset
state is maintained. When RESETIN goes LOW, the
device start-up sequence is executed (see Section 6.22).
6.21.2
E
XTERNAL POWER
-
ON RESET USING THE
RESETIN
PIN
An automatic reset can be obtained by connecting the
RESETIN pin to V
BAT
via a capacitor and to V
SS
via a
resistor. At power-on, the voltage on the RESETIN pin is
equal to V
BAT
and decreases from V
BAT
as the capacitor
charges through the resistor to V
SS
. V
RESETIN
must remain
higher than the threshold of the Schmitt trigger for a
duration of t
RESETIN
(see Chapter “AC characteristics”).
The reset configuration is shown in Fig.35.
6.21.3
INTERNAL
R
ESET
The watchdog which is available in the PCA5010
(see Section 6.16) will force a reset if it is enabled and
expires.
A reset is also forced, when the DC/DC converter restarts
operation from off mode (see Section 6.22.3).
All resets to the microcontroller can be observed as
negative pulses at the output RESOUT.
Fig.35 Application diagram for external power-on reset configuration.
handbook, full pagewidth
MGR344
VBAT
VBAT
VSS
RESETIN
RESET AND
POWER
CONTROLLER
internal reset
for microcontroller
RESOUT
PCA5010
watchdog
restart DC/DC
converter
10
μ
F
10 k
相關PDF資料 |
PDF描述 |
|---|---|
| PCA5010H | Pager baseband controller |
| PCA82C200 | STAND-ALONE CAN-CONTROLLER |
| PCA82C200P | STAND-ALONE CAN-CONTROLLER |
| PCA82C200T | STAND-ALONE CAN-CONTROLLER |
| PCA82C250 | CAN controller interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA5010H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller |
| PCA5010H/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|QFP|48PIN|PLASTIC |
| PCA503HL320 | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:ZIF FLEX CIRCUIT CONNECTOR |
| PCA503HU320 | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:ZIF FLEX CIRCUIT CONNECTOR |
| PCA503V320 | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:ZIF FLEX CIRCUIT CONNECTOR |
發布緊急采購，3分鐘左右您將得到回復。