- 您現在的位置：買賣IC網 > PDF目錄382377 > PCA5010 (NXP Semiconductors N.V.) Pager baseband controller PDF資料下載
參數資料
| 型號： | PCA5010 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Pager baseband controller |
| 中文描述： | 傳呼機基帶控制器 |
| 文件頁數： | 57/112頁 |
| 文件大?。?/td> | 627K |
| 代理商： | PCA5010 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
1998 Nov 02
57
Philips Semiconductors
Product specification
Pager baseband controller
PCA5010
6.19.6
P
ORT
1
INTERRUPTS
:P
ORT
1.0
TO
P
ORT
1.4(INT2
TO
INT6)
Four Port 1 lines can be used as external interrupt inputs
(see Fig.30). When enabled (IEN1 SFR), each of these
lines may wake-up the device from power-down. Using the
IX1 register, each of these port lines may be set active to
either HIGH or LOW. IRQ1 is the interrupt request flag
register. Each flag, if the interrupt is enabled, will send an
interrupt request, but must be cleared by software, i.e. via
the interrupt software. The Port 1 interrupt request flags
can only be set if the corresponding interrupt enable bit is
set.
6.19.7
M
: S
YM
C
LK
, DC/DC,
WATCHDOG
AND MINUTE
The decoder blocks generate events that can force an
interrupt when enabled (IEN0 and IEN1 SFR). These
interrupts are mapped to the corresponding P1 interrupt
request flag register bits (see Fig.33). Each flag, if the
interrupt is enabled, will send an interrupt request and
must be cleared by software, i.e. via the interrupt service
routine.
The IRQ bits are not set if the corresponding enable is not
set.
IRQ1.3:
(symbol interrupt): this interrupt request flag, if
enabled, is set if the demodulator (clock recovery) has
data ready, that should be read by the microcontroller.
The event is called symbol clock or SymClk, because in
one mode of operation one symbol is delivered per
interrupt. The flag is set by hardware and needs to be
cleared by software.
IRQ1.5:
(DC/DC converter interrupt); this interrupt
request flag, if enabled, is set if the DC/DC converter is
not able to deliver the required current (STB flag
cleared). The flag is set by hardware and needs to be
cleared by software.
IRQ1.6:
(watchdog interrupt); this interrupt request flag,
if enabled, is set if the watchdog timer will expire within
1
16
s. The flag is set by hardware and needs to be
cleared by software.
IRQ1.7:
(minute interrupt). This interrupt request flag, if
enabled, is set each minute once by the real-time clock.
The flag is set by hardware and needs to be cleared by
software.
Fig.32 Interrupt Port 1.0.
handbook, full pagewidth
MGR128
IX1.0
INT2
X2
IEN1.0
IRQ1.0
wake-up.0
Pad Port 1.0
0
1
Fig.33 SymClk (as example for any of the 4 mentioned interrupts).
handbook, full pagewidth
MGR129
IEN1.3
SymClk
CLOCK
RECOVERY
BLOCK
X5
IRQ1.3
相關PDF資料 |
PDF描述 |
|---|---|
| PCA5010H | Pager baseband controller |
| PCA82C200 | STAND-ALONE CAN-CONTROLLER |
| PCA82C200P | STAND-ALONE CAN-CONTROLLER |
| PCA82C200T | STAND-ALONE CAN-CONTROLLER |
| PCA82C250 | CAN controller interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA5010H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pager baseband controller |
| PCA5010H/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|QFP|48PIN|PLASTIC |
| PCA503HL320 | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:ZIF FLEX CIRCUIT CONNECTOR |
| PCA503HU320 | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:ZIF FLEX CIRCUIT CONNECTOR |
| PCA503V320 | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:ZIF FLEX CIRCUIT CONNECTOR |
發布緊急采購，3分鐘左右您將得到回復。