參數資料
型號： MD2534-D2G-X-P
廠商： SANDISK CORP
元件分類： 存儲控制器/管理單元
英文描述： FLASH MEMORY DRIVE CONTROLLER, PBGA115
封裝： 12 X 9 MM, 1.20 MM HEIGHT, FBGA-115
文件頁數： 16/87頁
文件大?。?/td> 1675K
代理商： MD2534-D2G-X-P
Rev. 1.2
Product Overview
mDOC H3 EFD Featuring Embedded TrueFFS Data Sheet
23
92-DS-1205-10
Signal
Ball No.
Signal Type
1
Description
Signal
Direction
Reserved
C2, C3, C4,
C5, C6, C7,
C8, C9,
C10, D1,
D2, D9,
D10, E9, F1,
F9, G1, H1,
J1, K1, K2,
L2, L9, L10,
M2, M3, M4,
M5, M6,M7,
M8, M9,
M10
-
All reserved signals are not connected
internally, and if not identified in this document
then it is recommended to leave them floating
to guarantee forward compatibility with future
products. They should not be connected to
arbitrary signals.
P1
ST/PU
Test Data In (JTAG).
Used for dedicated developer product only
4.
Input
M1
CMOS output Test Data Out (JTAG).
Used for dedicated developer product only
4.
Output
L1
ST/PU
Test Mode Select (JTAG)
Used for dedicated developer product only
4.
Input
RSRVD
N1
ST/PU
Test Clock (JTAG).
Used for dedicated developer product only
4.
Input
Mechanical
NC
A1, A2, A9,
A10, B1, B2,
B9, B10,
G5, G6, H5,
H6, N2, N9,
N10, P2,
P9, P10
-
Not Connected.
1.
The following abbreviations are used: ST - Schmidt Trigger input. IN/PD – CMOS input with internal pull down resistor (77K to 312K;
135K typical), which is enabled only when the 8KB memory window is in use, ST/PU - Schmitt Trigger input with internal pull up
resistor (95K to 261 K; 149 K typical).
2.
When mDOC H3 is used as a Master device, SO is used for Serial Interface Data In, and SI used for Serial Interface Data Out.
3.
The capacitor is required only for 1.8V Core and 1.8V I/O configuration. Please see section 9.5 for further details.
4.
The RSRVD JTAG balls will only be enabled on special versions of the mDOC H3 devices that will be used for debugging severe system
problems. In order to support this feature, the JTAG balls should be brought out to a separate header or test points. The JTAG RSRVD
balls must not be connected to the JTAG scan chain that is used for the rest of the PCB. If not used they should be left floating.
5.
BUSY#, DMARQ# and IRQ# should not be pulled up to any voltage higher than VCCQ. A pull-up resistor is required if this pin will be
connected to an input. A 10K ohm resistor to Vccq is recommended, however the exact value depends on system power, timing and signal
integrity requirements.
2.3.3
System Interface
See Figure 5 for a simplified I/O diagram of multiplexed interface mDOC H3. The power
connections and capacitors in this diagram are for illustration only. For detailed
recommendations regarding power connections and required capacitors, please refer to section
相關PDF資料
PDF描述
MD2533-D16G-X-P/Y FLASH MEMORY DRIVE CONTROLLER, PBGA115
MD2534-D1G-X-P FLASH MEMORY DRIVE CONTROLLER, PBGA115
MD2533-D8G-X-P FLASH MEMORY DRIVE CONTROLLER, PBGA115
SDED5-008G-NCY FLASH MEMORY DRIVE CONTROLLER, PBGA115
MD80C154-12/883 8-BIT, 12 MHz, MICROCONTROLLER, CDIP40
相關代理商/技術參數
參數描述
MD2534-D2G-X-P/Y 功能描述:IC MDOC H3 2GB 115-BGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:150 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (2 x 256 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-DFN（2x3） 包裝:管件 產品目錄頁面:1445 (CN2011-ZH PDF)
MD25A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:電焊機專用整流模塊MD25A1600V
MD25A1600V 制造商:未知廠家 制造商全稱:未知廠家 功能描述:光伏防反二極管模塊MD25A1600V技術參數資料、尺寸圖
MD25F20Z00 制造商:Positronic Industries 功能描述:
MD25M50000-14 制造商:POSITRONIC_IND 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*