參數資料
型號： MAX7000B
廠商： Altera Corporation
英文描述： Programmable Logic Device
中文描述： 可編程邏輯器件
文件頁數： 25/66頁
文件大小： 421K
代理商： MAX7000B
Altera Corporation
25
MAX 7000B Programmable Logic Device Data Sheet
Programmable Pull-Up Resistor
Each MAX 7000B device I/O pin provides an optional programmable
pull-up resistor during user mode. When this feature is enabled for an I/O
pin, the pull-up resistor (typically 50 k) weakly holds the output to
V
CCIO
level.
Bus Hold
Each MAX 7000B device I/O pin provides an optional bus-hold feature.
When this feature is enabled for an I/O pin, the bus-hold circuitry weakly
holds the signal at its last driven state. By holding the last driven state of
the pin until the next input signals is present, the bus-hold feature can
eliminate the need to add external pull-up or pull-down resistors to hold
a signal level when the bus is tri-stated. The bus-hold circuitry also pulls
undriven pins away from the input threshold voltage where noise can
cause unintended high-frequency switching. This feature can be selected
individually for each I/O pin. The bus-hold output will drive no higher
than V
CCIO
to prevent overdriving signals. The propagation delays
through the input and output buffers in MAX 7000B devices are not
affected by whether the bus-hold feature is enabled or disabled.
The bus-hold circuitry weakly pulls the signal level to the last driven state
through a resistor with a nominal resistance (R
BH
) of approximately
8.5 k.
Table 12
gives specific sustaining current that will be driven
through this resistor and overdrive current that will identify the next
driven input level. This information is provided for each VCCIO voltage
level.
The bus-hold circuitry is active only during user operation. At power-up,
the bus-hold circuit initializes its initial hold value as V
CC
approaches the
recommended operation conditions. When transitioning from ISP to User
Mode with bus hold enabled, the bus-hold circuit captures the value
present on the pin at the end of programming.
Table 12. Bus Hold Parameters
Parameter
Conditions
VCCIO Level
Units
1.8 V
2.5 V
3.3 V
Min
Max
Min
Max
Min
Max
Low sustaining current
High sustaining current
Low overdrive current
High overdrive current
V
IN
> V
IL
(max)
V
IN
< V
IH
(min)
0 V < V
IN
< V
CCIO
0 V < V
IN
< V
CCIO
30
50
70
μ
A
μ
A
μ
A
μ
A
–30
–50
–70
200
–295
300
–435
500
–680
相關PDF資料
PDF描述
MAX7000 Programmable Logic Device Family
MAX7000S Programmable Logic Device Family
MAX7030 RES 22.1-OHM 1% 0.1W 100PPM THICK-FILM SMD-0603 5K/REEL-7IN-PA
MAX7030-ATJ Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL
MAX7030HATJ Low-Cost, 315MHz, 345MHz, and 433.92MHz ASK Transceiver with Fractional-N PLL
相關代理商/技術參數
參數描述
MAX7000S 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Programmable Logic Device Family
MAX700C/D 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX700C/D DIE 制造商:Maxim Integrated Products 功能描述:
MAX700CPA 功能描述:監控電路 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX700CPA+ 功能描述:監控電路 Power-Supply Monitor w/Reset RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*