- 您現在的位置：買賣IC網 > PDF目錄384637 > M37920FGCGP (Mitsubishi Electric Corporation) Single Chip 16 Bits CMOS Microcomputer(16位單片機) PDF資料下載
參數資料
| 型號： | M37920FGCGP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| 中文描述： | 單片微機16位的CMOS（16位單片機） |
| 文件頁數： | 66/158頁 |
| 文件大?。?/td> | 1261K |
| 代理商： | M37920FGCGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
M37920FCCGP, M37920FCCHP
M37920FGCGP, M37920FGCHP
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
MITSUBISHI MICROCOMPUTERS
66
Receive
Receive is enabled when bit 2 (REi flag) of UARTi transmit/receive
control register 1 is set to
“
1.
”
As shown in Figure 62, the frequency
divider circuit (1/16) at the receiving side begin to work when a start
bit arrives and the data is received.
If RTSi output is selected by setting bit 2 of UARTi transmit/receive
control register 0 to
“
1
”
, the RTSi output is
“
H
”
when the REi flag is
“
0
”
. When the REi flag changes to
“
1
”
, the RTSi output goes
“
L
”
to
inform the receiver that reception has become enabled. When the
receive operation starts, the RTSi output automatically becomes
“
H
”
.
The entire transmission data bits are received when the start bit
passes the final bit of the receive block shown in Figure 52. At this
point, the contents of the receive register is transferred to the receive
buffer register and bit 3 (Rli flag) of UARTi transmit/receive control
register 1 is set to
“
1.
”
In other words, the RIi flag indicates that the
receive buffer register contains data when it is set to
“
1.
”
At this time,
when the low-order byte of the UARTk receive buffer register is read
out, RTSi output goes back to
“
L
”
to indicate that the register is ready
to receive the next data.
Bit 4 (OERi flag) of UARTi transmit/receive control register 1 is set to
“
1
”
when the next data is transferred from the receive register to the
receive buffer register while the RIi flag is
“
1
”
, in other words, when
an overrun error occurs. If the OERi flag is
“
1
”
, it indicates that the
next data has been transferred to the receive buffer register before
the contents of the receive buffer register has been read.
Bit 5 (FERi flag) is set to
“
1
”
when the number of stop bits is less than
required (framing error).
Bit 6 (PERi flag) is set to
“
1
”
when a parity error occurs.
Bit 7 (SUMi flag) is set to
“
1
”
when either the OERi flag, FERi flag, or
the PERi flag is set to
“
1.
”
Therefore, the SUMi flag can be used to
determine whether there is an error.
The RIi, OERi, FERi, and PERi flags are set to
“
1
”
while transferring
the contents of the receive register into the receive buffer register.
The FERi, PERi, and SUMi flags are cleared to
“
0
”
when the low-or-
der byte of the receive buffer register has been read out or when
“
0
”
has been written to the REi flag.
The OERi flag is cleared to
“
0
”
when
“
0
”
has been written to the REi
flag.
Interrupt request at completion of reception
When the RIk flag changes from
“
0
”
to
“
1
”
, in other words, when the
receive operation is completed, the interrupt request bit of the
UARTk receive interrupt control register can be set to
“
1
”
.
The timing when this interrupt request bit is to be set to
“
1
”
can be
selected from the following:
Each reception
When an error occurs at reception
If bit 5 of the UARTk transmit/receive control register 0 (UART re-
ceive interrupt mode select bit) is cleared to
“
0
”
, the interrupt request
bit is set to
“
1
”
at each reception. If bit 5 is set to
“
1
”
, the interrupt re-
quest bit is set to
“
1
”
only when an error occurs. (In the clock asyn-
chronous serial communication, when an overrun error, framing
error, or parity error occurs, the interrupt request bit is set to
“
1
”
.)
Sleep mode
The sleep mode is used to communicate only between certain micro-
computers when multiple microcomputers are connected through
serial I/O.
The microcomputer enters the sleep mode when bit 7 of UARTi
transmit/receive mode register is set to
“
1.
”
The operation of the sleep mode for an 8-bit asynchronous commu-
nication is described below.
When sleep mode is selected, the contents of the receive register is
not transferred to the receive buffer register if bit 7 (bit 6 if 7-bit asyn-
chronous communication and bit 8 if 9-bit asynchronous communi-
cation) of the received data is
“
0
”
. Also the RIi, OERi, FERi, PERi,
and the SUMi flags are unchanged. Therefore, the interrupt request
bit of the UARTi receive interrupt control register is also unchanged.
Normal receive operation takes place when bit 7 of the received data
is
“
1
”
.
The following is an example of how the sleep mode can be used.
The main microcomputer first sends data: bit 7 is
“
1
”
and bits 0 to 6
are set to the address of the subordinate microcomputer to be com-
municated with. Then all subordinate microcomputers receive this
data. Each subordinate microcomputer checks the received data,
clears the sleep bit to
“
0
”
if bits 0 to 6 are its own address and sets
the sleep bit to
“
1
”
if not. Next, the main microcomputer sends data
with bit 7 cleared. Then the microcomputer which cleared the sleep
bit will receive the data, but the microcomputers which set the sleep
bit to
“
1
”
will not. In this way, the main microcomputer is able to com-
municate only with the designated microcomputer.
相關PDF資料 |
PDF描述 |
|---|---|
| M37920FCCGP | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37920FCCHP | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M37920FGCHP | Single Chip 16 Bits CMOS Microcomputer(16位單片機) |
| M3802 | Single Chip 8 Bits Microcomputer(8位單片機) |
| M3820 | Single Chip 8 Bits Microcomputer(8位單片機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37920FGCHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
| M37920S4CGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
| M37P75C4P3 | 功能描述:汽車連接器 Pin Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel |
| M37S07K4F3 | 功能描述:汽車連接器 Sckt Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel |
| M37S07K4P3 | 功能描述:汽車連接器 Sckt Contacts RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel |
發布緊急采購，3分鐘左右您將得到回復。