參數資料
型號： M37920FGCGP
廠商： Mitsubishi Electric Corporation
英文描述： Single Chip 16 Bits CMOS Microcomputer(16位單片機)
中文描述： 單片微機16位的CMOS（16位單片機）
文件頁數： 65/158頁
文件大小： 1261K
代理商： M37920FGCGP
65
M37920FCCGP, M37920FCCHP
M37920FGCGP, M37920FGCHP
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
MITSUBISHI MICROCOMPUTERS
Once transmission has started, the TEi flag, TIi flag, and CTSi signal
are ignored until data transmission is completed.
Therefore, transmission does not stop until it completes event if, dur-
ing transmission, the TEi flag is cleared to
“
0
”
or CTSi input is set to
“
1
”
.
CTSi is checked while the T
END
i signal shown in Figure 60 is
“
H
”
.
Therefore, data can be transmitted continuously if the next transmis-
sion data is written in the transmit buffer register and TIi flag is
cleared to
“
0
”
before the T
END
i signal goes
“
H
”
.
Bit 3 (T
X
EPTYi flag) of UARTi transmit/receive control register 0
changes to
“
1
”
at the next cycle just after the T
END
i signal goes
“
H
”
and changes to
“
0
”
when transmission starts. Therefore, this flag can
be used to determine whether data transmission is completed.
When the TIi flag changes from
“
0
”
to
“
1
”
, the interrupt request bit of
the UARTi transmit interrupt control register is set to
“
1
”
.
Transmission
Transmission is started when bit 0 (TEi flag transmit enable flag) of
UARTi transmit/receive control register 1 is
“
1
”
, bit 1 (TIi flag) is
“
0
”
,
and CTSi input (in other words, transmit enable signal input from re-
ceiver) is
“
L.
”
The TIi flag indicates whether the transmit buffer is
empty or not. It is cleared to
“
0
”
when data is written in the transmit
buffer; it is set to
“
1
”
when the contents of the transmit buffer register
is transferred to the transmit register.
When all of the transmission conditions are satisfied, transmit data
is transferred to the transmit register, and transmit operation starts.
As shown in Figures 60 and 61, data is output from the T
X
Di pin with
the stop bit or parity bit specified by bits 4 to 6 of UARTi transmit/re-
ceive mode register. The data is output from the least significant bit.
When the transmit register becomes empty after the contents has
been transmitted, data is transferred automatically from the transmit
buffer register to the transmit register if the next transmit start condi-
tion is satisfied. Then, the next transmission is performed
succeedingly.
Fig. 62 Receive timing example when 8-bit asynchronous communication with no parity and 1 stop bit selected
Start bit
Stop bit
Start bit
D
0
D
1
D
7
Check to be
“
L
”
level
Starting at the falling
edge of start bit
Data fetched
f
i
or f
EXT
RE
i
R
X
D
i
Receive
clock
RI
i
RTS
i
相關PDF資料
PDF描述
M37920FCCGP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37920FCCHP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37920FGCHP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M3802 Single Chip 8 Bits Microcomputer(8位單片機)
M3820 Single Chip 8 Bits Microcomputer(8位單片機)
相關代理商/技術參數
參數描述
M37920FGCHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920S4CGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
M37P75C4P3 功能描述:汽車連接器 Pin Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
M37S07K4F3 功能描述:汽車連接器 Sckt Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
M37S07K4P3 功能描述:汽車連接器 Sckt Contacts RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*