參數資料
型號： M37920FGCGP
廠商： Mitsubishi Electric Corporation
英文描述： Single Chip 16 Bits CMOS Microcomputer(16位單片機)
中文描述： 單片微機16位的CMOS（16位單片機）
文件頁數： 117/158頁
文件大?。?/td> 1261K
代理商： M37920FGCGP
117
M37920FCCGP, M37920FCCHP
M37920FGCGP, M37920FGCHP
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
MITSUBISHI MICROCOMPUTERS
Flash Memory Parallel I/O Mode
The flash memory parallel I/O mode is used to manipulate the inter-
nal flash memory with a parallel programmer. This parallel program-
mer uses the software commands listed in Table 25 to do the flash
memory manipulations, such as read/programming/erase opera-
tions.
In the flash memory parallel I/O mode, each block can be protected
from erasing/programming (in other words, block lock).
Table 25. Software commands (flash memory parallel I/O mode)
Software Command
Read Array
Read Status Register
Clear Status Register
Page Programming
(Note)
Block Erase
Erase All Unclocked Block
Lock Bit Programming
Read Lock Bit Status
Note:
Programming is performed in a unit of 256 bytes, with the low-order
address assigned in the range of 00
16
—
FF
16
(byte addresses).
User ROM Area and Boot ROM Area
The user ROM area and boot ROM area can be reprogrammed in
the flash memory parallel I/O mode.
The programming and block erase operations can be performed only
to these areas.
The boot ROM area, 16 Kbytes in size, is assigned to addresses
0000
16
–
3FFF
16
(byte addresses), so that programming and block
erase operations can be performed only to this area. (Access to any
address out of this area is prohibited).
The erasable block in the boot ROM area is only one block, consist-
ing of 16 Kbytes. The reprogramming control firmware to be used in
the flash memory serial I/O mode has been stored to this boot ROM
area on our shipment. Therefore, do not reprogram the boot ROM
area if the user uses the flash memory serial I/O mode.
Addresses FFB0
16
to FFBF
16
are the reserved area for the serial
programmer. Therefore, when the user uses the flash memory serial
I/O mode, do not program to this area.
Note that, when the boot ROM area is read out from the CPU in the
CPU reprogramming mode, described later, its addresses will be
shifted to C000
16
—
FFFF
16
(byte addresses).
相關PDF資料
PDF描述
M37920FCCGP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37920FCCHP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37920FGCHP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M3802 Single Chip 8 Bits Microcomputer(8位單片機)
M3820 Single Chip 8 Bits Microcomputer(8位單片機)
相關代理商/技術參數
參數描述
M37920FGCHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920S4CGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
M37P75C4P3 功能描述:汽車連接器 Pin Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
M37S07K4F3 功能描述:汽車連接器 Sckt Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
M37S07K4P3 功能描述:汽車連接器 Sckt Contacts RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*